Husqvarna 16530-LS Скачать руководство пользователя

Страница: 7 / 24

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR

HEAD (See Fig. 7)
NOTE:

The multi-wrench provided in your parts bag may

be used to install the chute rotator head.
1. Place discharge chute assembly on top of chute base

with discharge opening toward front of snow thrower.

2. Position chute rotator head over chute bracket. If nec es -

sary, rotate chute assembly to align square and pin on un-

der side of chute rotator head with holes in chute brack et.

3. With chute rotator head and chute bracket aligned,

po si tion chute rotator head on pin and threaded stud

of mounting bracket.

4. Install 3/8 washer and locknut on threaded stud and

tighten securely.

INSTALL CHUTE DEFLECTOR REMOTE CONTROL

(See Figs. 8 and 9)

1. Install remote cable bracket to discharge chute with

5/16-18 carriage bolt and 5/16-18 locknut as shown.

Tighten securely.

2. Install remote cable eyelet to chute deflector with 1/4-20

shoulder bolt and 1/4-20 locknut as shown. Tighten

nut securely. Eyelet will be loose on shoulder bolt.

3. Install spring hooks between hex nuts on chute rotator

head and into hole in chute deflector as shown.

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac-

tory for shipping purposes. Correct and equal tire pres sure

is important for best snow throwing performance.
• Reduce tire pressure to 14-17 PSI.

CHUTE

ROTATOR

HEAD

3/8 WASHER

3/8 LOCKNUT

THREADED

STUD

PIN

ROTATOR HEAD

MOUNT ING

BRACKET

CHUTE

BRACKET

Fig. 7

ALIGN BEFORE

TIGHTENING LOCKNUT

Fig. 8

ASSEMBLY / PRE-OPERATION

HOOK

BE TWEEN

HEX NUTS

ON CHUTE

ROTATER

HEAD

SPRING

CHUTE

DE FLEC TOR

5/16-18

CARRIAGE

BOLT

5/16-18

LOCKNUT

REMOTE

CABLE

BRACKET

1/4-20

LOCK NUT

CABLE

EYELET

1/4-20

SHOULDER

BOLT

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

Содержание 16530-LS

























Результаты поиска

Содержание 16530-LS

Отзывы:

Похожие инструкции для 16530-LS

Бренды по названию

Популярные бренды

Husqvarna 16530-LS, Руководство оператора

Результаты поиска

Содержание 16530-LS

Отзывы:

Похожие инструкции для 16530-LS

Бренды по названию

Популярные бренды