background image

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

40 – English

YOUR WARRANTY RIGHTS AND 
OBLIGATIONS

The EPA (The US Environmental Protection Agency), 
Environment Canada and Husqvarna Forest & Garden 
are pleased to explain the emissions control system 
warranty on your 2001 and later small nonroad engine. In 
U.S. and Canada, new small nonroad engines must be 
designed, built and equipped to meet the federal stringent 
anti-smog standards. Husqvarna Forest & Garden must 
warrant the emission control system on your small 
nonroad engine for the period of time listed below 
provided there has been no abuse, neglect or improper 
maintenance of your unit. Your emission control system 
includes Parts such as the carburetor and the ignition 
system. Where a warrantable condition exists, Husqvarna 
Forest & Garden will repair your small nonroad engine at 
no cost to you. Expenses covered under warranty include 
diagnosis, parts and labor.

MANUFACTURER

′′′′

S WARRANTY 

COVERAGE

The 2001 and later small nonroad engines are warranted 
for two years. If any emission related part on you engine 
(as listed above) is defective, the part will be repaired or 
replaced by Husqvarna Forest & Garden.

OWNER

′′′′

S WARRANTY 

RESPONSIBILITIES

As the small nonroad engine owner, you are responsible 
for the performance of the required maintenance listed in 
your Operator

s Manual. Husqvarna Forest & Garden 

recommends that you retain all receipts covering 
maintenance on your small nonroad engine, but 
Husqvarna Forest & Garden cannot deny warranty solely 
for the lack of receipts or for your failure to ensure the 
performance of all scheduled maintenance. As the small 
nonroad engine owner, you should, however, be aware 
that Husqvarna Forest & Garden may deny you warranty 
coverage if your small nonroad engine or a part of it has 
failed due to abuse, neglect, improper maintenance, 
unapproved modifications or the use of parts not made or 
approved by the original equipment manufacturer. You are 
responsible for presenting your small nonroad engine to a 
Husqvarna Forest & Garden authorized servicing dealer 
as soon as a problem exists. The warranty repairs should 
be completed in a reasonable amount of time, not to 
exceed 30 days. If you have any questions regarding your 
warranty rights and responsibilities, you should contact 
your nearest authorized servicing dealer or call 
Husqvarna Forest & Garden at 1-800-487-5963.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad 
engine is delivered.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the initial owner 
and each subsequent purchaser that the engine is free 
from defects in materials and workmanship which cause 
the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

 Repair or 

replacement of any warranted part will be performed at no 
charge to the owner at an approved Husqvarna Forest & 
Garden servicing dealer. If you have any questions 
regarding your warranty rights and responsibilities, you 
should contact your nearest authorized servicing dealer 
or call Husqvarna Forest & Garden at 1-800-487-5963.

WARRANTY PERIOD

 Any warranted part which is not 

scheduled for replacement as required maintenance, or 
which is scheduled only for regular inspection to the effect 
of “repair or replace as necessary” shall be warranted for 
2 years. Any warranted part which is scheduled for 
replacement as required maintenance shall be warranted 
for the period of time up to the first scheduled 
replacement point for that part.

DIAGNOSIS

 The owner shall not be charged for 

diagnostic labor which leads to the determination that a 
warranted part is defective, if the diagnostic work is 
performed at an approved Husqvarna Forest & Garden 
servicing dealer.

CONSEQUENTIAL DAMAGES

 Husqvarna Forest & 

Garden may be liable for damages to other engine 
components caused by the failure of a warranted part still 
under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper 
maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for 
disallowing a warranty claim. Husqvarna Forest & Garden 
is not liable to cover failures of warranted parts caused by 
the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights 
and responsibilities, you should contact your nearest 
authorized servicing dealer or call Husqvarna Forest & 
Garden at 1-800-487-5963.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all 
Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND 
REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement 
part used in the performance of any warranty 
maintenance or repairs on emission-related parts, will be 
provided without charge to the owner if the part is under 
warranty.

Содержание 1153176-95













































Отзывы: