background image

 

www.usa.husqvarna.com

 

WARNING

Contact with muffler area can result in serious 

burns.
Exhaust heat/gases can ignite combustibles, 

structures or damage fuel tank causing a fire.

•  DO NOT touch hot parts and AVOID hot exhaust gases.
•  Allow equipment to cool before touching.
•  Keep at least 5 feet (1.5 m) of clearance on all sides of 

generator including overhead.

•  Code of Federal Regulation (CFR) Title 36 Parks, Forests, and 

Public Property require equipment powered by an internal 

combustion engine to have a spark arrester, maintained in 

effective working order, complying to USDA Forest service 

standard 5100-1C or later revision. In the State of California a 

spark arrester is required under section 4442 of the California 

Public resources code. Other states may have similar laws.

 

WARNING

Starter and other rotating parts can entangle 

hands, hair, clothing, or accessories.

•  NEVER operate generator without protective housing or covers.
•  DO NOT wear loose clothing, jewelry or anything that may be 

caught in the starter or other rotating parts.

•  Tie up long hair and remove jewelry.

 

WARNING

Unintentional sparking can result in fire or 

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO yOUR GENERATOR

•  Disconnect the spark plug wire from the spark plug and place 

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

•  Use approved spark plug tester.
•  DO NOT check for spark with spark plug removed.

 

CAUTION

Excessively high operating speeds increase risk of injury 

and damage to generator.
Excessively low speeds impose a heavy load.

•  DO NOT tamper with governed speed. Generator supplies 

correct rated frequency and voltage when running at governed 

speed.

•  DO NOT modify generator in any way.

NOTICE

Exceeding generators wattage/amperage capacity can 

damage generator and/or electrical devices connected to 

it.

•  DO NOT exceed the generator’s wattage/amperage capacity. 

See 

Don’t Overload Generator

 in the 

Operation

 section.

•  Start generator and let engine stabilize before connecting 

electrical loads.

•  Connect electrical loads in OFF position, then turn ON for 

operation.

•  Turn electrical loads OFF and disconnect from generator before 

stopping generator.

NOTICE

Improper treatment of generator can damage it and 

shorten its life.

•  Use generator only for intended uses.
•  If you have questions about intended use, ask dealer or contact 

local service center.

•  Operate generator only on level surfaces.
•  DO NOT expose generator to excessive moisture, dust, dirt, or 

corrosive vapors.

•  DO NOT insert any objects through cooling slots.
•  If connected devices overheat, turn them off and disconnect 

them from generator.

•  Shut off generator if: 

 

-electrical output is lost; 

 

-equipment sparks, smokes, or emits flames; 

 

-unit vibrates excessively.

Содержание 1055 GN






























Отзывы: