Husky HU3650 Скачать руководство пользователя страница 12

  

12

SERVICE AND STORAGE

INFREQUENT SERVICE

If the unit is used infrequently, difficult starting may result. 

to eliminate hard starting, run the generator at least 30 minutes 
every month. Also, if the unit will not be used for some time, it is 
a good idea to drain the fuel from the carburetor and gas tank.

LONG TERM STORAGE

When the generator set is not being operated or is being 

stored more than one month, follow these instructions:

 

Replenish engine lubricant to upper level.

 

Drain gasoline from fuel tank, fuel line and carburetor.

  a)  Turn the engine switch off ( O ).

  b)  Close fuel valve.
  c)  Remove the fuel line from the petcock by squeezing the 

ends of the retaining clip and sliding the fuel line off.

  d)  Install one end of a drain line over the petcock, and place 

the other end in a fuel container large enough to catch the 
fuel being drained from the tank.

  e)  Open fuel valve.
  f)  When  the  fuel  has  drained  from  the  tank,  close  the  fuel 

valve and reinstall fuel line on petcock.

 

Pour  about  one  teaspoon  of  engine  lubricant  through  the 
spark  plug  hole,  pull  the  recoil  starter  several  times  and 
replace the plug. Then pull the starter until you feel the pis-
ton is on its compression stroke and leave it in that position. 
This closes both the intake and exhaust valves to prevent the 
inside of the cylinder from rusting.

 

Cover the unit and store in a clean, dry place that is well ven-
tilated away from open flame or sparks.

NOTE:  we  recommend  always  using  a  fuel  stabilizer. 

A  fuel  stabilizer  will  minimize  the  formulation  of  fuel  gum 

deposits during storage. The fuel stabilizer can be added to 

the gasoline in the fuel tank, or into the gasoline in a storage 

container.

Do not store unit with fuel in the tank.

LIMITED wARRANTy

wARRANTy COVERAGE

Techtronic Industries North America, Inc., (the Company) warrants 

to the original retail purchaser that this Husky Product is free from 

defects in material and workmanship and agrees to repair or replace, 

at  the  Company’s  sole  discretion,  any  defective  Product  free  of 

charge within these time periods from the date of purchase:

 

Three years, if the Product is used solely for personal, family, or 

household use;

 

One year, if the Product is used for business or commercial use.

This  warranty  applies  only  to  Products  sold  within  the  United 

States  of  America,  the  District  of  Columbia,  Canada,  Mexico,  the 

Commonwealth of Puerto Rico, the Virgin Islands, Guam, the Canal 

Zone, or American Samoa.
This  warranty  is  not  transferable  and  does  not  cover  damage 

resulting  from  defects  other  than  in  material  or  workmanship,  or 

damage caused by unreasonable use, including the failure to provide 

reasonable and necessary maintenance. 

Other items not covered 

under this warranty include:

 

Transportation charges for sending the product to the Company 

or its authorized service representative for warranty service, or for 

shipping repaired or replacement products back to the customer; 

these charges must be borne by the original retail purchaser.

 

Engine. Your Product is equipped with an engine that is covered 

exclusively by a separate warranty from the engine manufacturer. 

Please refer to the engine manual included with the Product for 

warranty information related to the engine. 

 

Damages caused by abuse, accident, misuse, neglect, alteration, 

modification, the effects of corrosion, erosion, normal wear and 

tear  or  repairs  by  other  than  the  Company  or  its  authorized 

service representative. 

Warranty  is  voided  if  the  customer  fails  to  install,  maintain  and 

operate  the  product  in  accordance  with  the  instructions  and 

recommendations  of  the  Company  as  set  forth  in  the  Product’s 

operator’s manual or if the Product is used as rental equipment.

The Company will not pay for repairs or adjustments to the Product, 

or  for  any  costs  or  labor,  performed  without  the  Company’s  prior 

authorization.

SAVE yOUR SALES SLIP

Proof of purchase in the form of your dated sales receipt, cash register 

slip, etc. showing the serial number and the model of your Product 

will be required before the Company and/or its authorized service 

representatives can perform warranty service on the Product.

EXCLUSIONS AND LIMITATIONS

THIS LIMITED wARRANTy IS IN LIEU OF ALL OTHER EXPRESS 

wARRANTIES. 

ANY IMPLIED WARRANTY OF MERCHANTABILITY, 

FITNESS  FOR  A  PARTICULAR  PURPOSE,  OR  OTHERWISE, 

APPLICABLE  TO  THIS  PRODUCT,  SHALL  BE  LIMITED  IN 

DURATION TO THE DURATION OF THIS LIMITED WARRANTY. THE 

WARRANTY  SERVICE  DESCRIBED  ABOVE  IS  THE  EXCLUSIVE 

REMEDY UNDER THIS WARRANTY. THE COMPANY SHALL NOT 

BE LIABILE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES.

SOME STATES DO NOT ALLOW A LIMITATION ON THE DURATION 

OF IMPLIED WARRANTIES, OR THE EXCLUSION OR LIMITATION 

OF  INCIDENTAL,  OR  CONSEQUENTIAL  DAMAGES,  SO  THE 

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. 

HOw TO ObTAIN wARRANTy SERVICE

For warranty service: Call toll free 1-866-340-3912, or write to 

Techtronic Industries North America, Inc., P.O. box 35, Hwy. 8, 

Pickens, SC 29671. 
For warranty service outside the USA, please contact your local 

Husky dealer. 

Содержание HU3650































Отзывы: