background image

Version April 2016

EN

 11

HÜRNER HST 300   2.0 User’s Manual

H Ü R N E R   S c h w e i s s t e c h n i k   G m b H

Nieder-Ohmener Str. 26

35325 Mücke, Germany

5.6  End of Welding

The welding process ends successfully if the actual weld-
ing time corresponds to the nominal welding time and the 
buzzer can be heard twice.

5.7  Aborted Welding Process

The welding process has failed if a plain-text error is dis-
played on the screen and the audible signal buzzes con-
tinuously. An error has to be acknowledged by pressing 
the STOP/RESET key.

5.8  Cooling Time

The cooling time as given in the fitting manufacturer’s 
instructions has to be respected. If the bar code provided 
by the fitting manufacturer contains  cooling time data, 
it will be displayed at the end of the welding process and 
will be counted down to zero. This countdown can be ac-
knowledged and canceled at any time by the STOP/RESET 
key. However, note that for that time the pipe fitting joint 
which is still warm must not be subjected to an external 
force. No cooling time is displayed if the fitting code does 
not contain any such information.

5.9  Returning to the Start of Parameter Input

After welding is finished, disconnecting the welded fitting 
from the unit or pressing the STOP/RESET key will reset the 
unit back to the start of entering the welding parameters.

5.10 Using ViewWeld to View Welding Reports

The ViewWeld feature offers viewing an abstracted version 
of the welding report recorded during the last welding 
process. The ViewWeld abstract shows the report number, 
the date and time of the welding and the welding param-
eters along with an evaluation of the quality of the joint/
welding operation (see Display 5).

To call the ViewWeld abstract of a welding report, press 
the 

ñ

 key in the bar code input screen (see Display 2).

Entering Welding Parameters Manually 

(only for model version HST 300   2.0)

To be able to enter the welding parameters manually, you 
have first to connect the fitting to the welding unit with 
the welding cable. The manual input of the parameters can 
then be accessed by pressing the 

ò

 arrow key. The screen 

Display 5

0015  24.02.13 09:33

M/B  MON HST  315

0058s  025.0V  1.57Ω

Welding OK

Display 6

**  MANUAL INPUT  **
>Enter Voltage/Time

 Enter Fitting Code

Содержание HST 300 Junior + 2.0




















Отзывы: