Huntleigh Baby DOPPLEX 4000 Скачать руководство пользователя страница 46

Страница: 46 / 76

10.11

Print Head Refitting

1. Fit print head connector, head mounting plate and tighten 6 screws to 35cNm.

Ensure that print head is parallel to head mounting plate.

2. Place spacers over pillars and springs over spacers.
3. Place head support plate over head mounting plate ensuring that metal tongue

is located under screw head as fig 13.

4. Push print head support plate past pillars, fit plain washers over pillars, tighten

nuts to 35cNm. Ensure that print head support plate and head mounting plate

are free to slide up and down spacers.

5. Place print head assembly over mounting pillars and screws. Align print head

as detailed in 7.12.

10.12

Print Head Alignment Procedure

1. With print head assembly screws tightened lightly and ribbon cable connected,

pull print head towards front of unit and close paper tray.

2. Ensure that front panel ribbon cable is connected to main PCB and connect

mains supply to inlet socket.

Issue: 2 DRAFT

Rev: a

614365

Warning - Shock Hazard

Extreme caution must be taken while working in live

equipment, ensure that earthed case does not contact live

parts. Also note that parts of the power supply are live.

Fig 13 Print Head Assembly

Содержание Baby DOPPLEX 4000













































































Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды

Huntleigh Baby DOPPLEX 4000, Руководство по обслуживанию

Результаты поиска

Содержание Baby DOPPLEX 4000

Отзывы:

Похожие инструкции для Baby DOPPLEX 4000

Бренды по названию

Популярные бренды