Hunter WVC-100 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 16

Hunter WVC-100 Скачать руководство пользователя страница 11

11

Connecting a Weather Sensor

Connecting a Weather Sensor

A Hunter Mini-Clik

®

rain sensor or other micro-switch-

type weather sensor can be connected to the WVC. The
purpose of this sensor is to stop watering when weather
conditions dictate.

To Connect a Weather Sensor to the WVC

1. Cut the yellow wire loop attached to the WVC at

approximately the middle of the loop.

2. Remove approximately ½" (13 mm) of insulation from

each wire. Attach each wire to each of the wires of the
weather sensor.

3. Secure both wire connections with waterproof

connectors.

Programming the Controller

The WVC is simple to program with its companion,
the WVP Wireless Valve Programmer. The easy-to-
understand push-button design of the WVP allows you to
step through the process of programming and activating
manual watering with the press of a button. Further
information on operating the WVP can be found in your
WVP Owner’s Manual.

«
...
9
10
11
12
13
...
»

Содержание WVC-100

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды