background image

www.HunterFan.com

1.888.830.1326

M0035-01 • 05/28/13 • © Hunter Fan Company

17

Troubleshooting

    Excessive wobbling

•  Tighten all of the blade and 

blade iron screws until they 
are snug.

•  Use the provided balancing 

kit and instructions to balance 
the fan.

    Noisy Operation

•  Tighten the blade and blade 

iron screws until they are snug.

•  Check to see if any of the 

blades are cracked. If so, replace 
all of the blades.

    Fan doesn’t work

•  Make sure power switch is on.

•  Pull the pull chain to make sure 

it is on.

•  Push the motor reversing switch 

firmly left or right to ensure that 
it is engaged.

•  Check the circuit breaker to 

ensure the power is turned on.

•  Make sure the blades spin freely.

•  Turn off power from the circuit 

breaker, then loosen the canopy 
and check all the connections 
according to the wiring diagram 
on page 7.

•  Check the plug connection in 

the switch housing.

Hunter fans have the power to cut your cooling costs up 
to 40%.

Beat the High Cost of Cooling

The air movement created by a Hunter ceiling fan 
lets you set your thermostat higher and still stay 
comfortable. Every degree you raise the thermostat 
saves up to 7% on energy costs. So, you can cut back on 
expensive air conditioning ... and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air 
and saves up to 10%* on heating bills.
* On average at low speed settings. Your savings may 
vary based on climate, building type and thermostat 
setting.

Save Energy and Money While Protecting 
the Environment 

Congratulations! You’re saving energy and money while 
protecting the environment by purchasing this ENERGY 
STAR qualified Hunter ceiling fan! With this purchase, you 
are doing your part to protect the environment. In 2010, 
ENERGY STAR qualified ceiling fans are projected to cut 
air pollution by more than 500 million pounds!
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efficiency specifications 
set by the Environmental Protection Agency (EPA). 
ENERGY STAR labeled ceiling fans save energy because 
they have more efficient fan motors and air delivery due 
to more aerodynamic blade configurations. Ceiling fan 
models bearing the ENERGY STAR label move air 14 - 
20% more efficiently than typical ceiling fan models.
For more information on ENERGY STAR visit www.
energystar.gov.

Содержание M0035-01


















Отзывы: