Hunter ACC-COM-LTE Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

background image

2

Introduction

Items Included:

• (1) ACC-COM-LTE or ACC-P2P-LTE module,

including internal (pre-installed) SIM card

•  (1) Antenna
•  (1) Tube of RTV sealant
•  (1) Cleaning wipes

Tools/Supplies Required (Not Included):

•  Small Phillips screwdriver with magnetic tip
•  Small flathead screwdriver
•  Additional tools and hardware as required for antenna mounting (radio only)
•  Pedestal mount requires APPBRKT2 (sold separately)

Ribbon cable

Mounting screws

Mounting screws

Enter button

Module Operation

The ACC-COM-LTE provides cellular mobile communications for ACC series
controllers from a central computer.
This module may be installed in wall-mounted or pedestal-mounted
controllers.

Communication Module

«
1
2
3
4
...
»

Содержание ACC-COM-LTE

















Отзывы:

Нет отзывов

Похожие инструкции для ACC-COM-LTE

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: E-fly Страницы: 16

Бренд: Nedap Страницы: 20

Бренд: Ultratec Страницы: 33

Бренд: Vag Страницы: 15

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

Бренд: Multi-Clean Страницы: 4

Бренд: Primo Water Страницы: 10

Бренд: PENGWYN Страницы: 32

Бренд: Warner Electric Страницы: 6

Бренд: HEIDENHAIN Страницы: 257

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды