Hunter 42606-01 Скачать руководство пользователя страница 6

Страница: 6 / 14

Hunter Fan Company

42606-01 • 11/18/05

Hunter Fan Company

3 • Assembling the Fan

Steps 3-2 – 3-3

Low Profile

Washer

Downrod

Canopy

Set Screw

Locking Screw

WARNING:

Fan may fall if not assembled as directed in these

installation instructions.

3-1. Unbundle the wires from the fan.

For Standard or Angle mounting:

3-2. Insert the downrod through the canopy and canopy trim ring.

Feed the wires from the fan through the downrod on one side of
the pin in the ball.

3-3. Loosen the square head set screw on the adapter to install the

pipe and ball assembly.

Note:

When the pipe and ball assembly

is fully installed, 2-3 threads on the pipe will still be visible; this is
normal. Securely retighten the set screw with a wrench or pliers.
Go to

4 • Hanging and Wiring the Fan

CAUTION:

e adapter has a special coating on the threads. Do

not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.

For Low Profile mounting:
Note:

For low profile mounting, the downrod is replaced with the

low profile washer.

3-4.  Remove the set screw from the adapter.
3-5.  Place the low profile washer into the canopy with the lip down.
3-6.  Align the holes in the washer with the holes in the adapter.

Assemble securely with three locking screws. Go to

4 • Hanging

and Wiring the Fan

Canopy

Trim Ring

Green

Ground

Wire

Standard or Angle Mounting

Low Profile Mounting

Locking Screws

Canopy

Trim Ring

Adapter

Low Profile

Washer

Locking Screws

Steps 3-5 – 3-6

Step 3-6 (Detail)

Содержание 42606-01















Результаты поиска

Содержание 42606-01

Отзывы:

Бренды по названию

Популярные бренды

Hunter 42606-01, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 42606-01

Отзывы:

Бренды по названию

Популярные бренды