2. To change the setting to 45°F (7°C) (blinking
light ON) touch and release the wet switch
contacts once more. Wait two seconds and then
confirm that the temperature reading on the
Control Head has changed to 45°F (7°C). Single
touches will toggle the setting between 40°F
(4°C) and 45°F (7°C).
NOTE:
When the LED is set to ON it will flash every four seconds when
the RSS™ is in operation (i.e. when the wet switch is submerged).
Even when the LED is set to ON, the LED will not flash unless the wet
switch is activated. If you want to test the RSS™ to make sure the LED
is set to ON before using the RSS™, wet your finger and hold it on the
wet switch; if the LED is set to ON, the LED will begin to flash.
NOTE:
Repeat steps 1 and 2 to turn off the LED when finished with
night fishing.
3. Once you have made your selection you can
either wait 20 seconds for programming mode to
time out (the Start-Up screen will appear on the
Control Head display), or continue immediately to
the next procedure to change the channel.
Changing the Channel on the Advanced RSS™
To change the channel type on the Advanced RSS™:
1. From the Light programming mode (see
Turning on the Advanced RSS™ Blinking
Light
), touch and release the wet switch
contacts twice more with your moist finger to
change from the Light programming mode to
the Channel programming mode.
The
temperature reading on the Control Head will
change to show a temperature reading of 50°F
(9°C) (channel set to A).
2. To change the setting to 55°F (12°C) (channel
set to B) touch and release the wet switch
contacts once more. Wait two seconds and
then confirm that the temperature reading on
the Control Head has changed to 55°F (12°C).
Single touches will toggle the setting between
50°F (9°C) and 55°F (12°C).
3. Once you have made your selection, wait 20
seconds for programming mode to time out (the
Start-Up screen will appear on the Control
Head).
4. Use the SetUp Channel Select menu on the
Control Head to switch the software to match
the new channel designation on the Advanced
RSS™. See
Channel Select (SetUp Menu)
for
more information.
CAUTION:
Make sure that you change the Channel Selection on the
Control Head to match the new Advanced RSS™ Channel before
using the Advanced RSS™.
Using a First Generation RSS™
First generation RSS™ units still sold with other
SmartCast
®
products come in two versions, Channel A
and Channel B (RF40A and RF40B), and are both
compatible with the RF25.
NOTE:
When using either an RF40A or RF40B RSS™ with the RF25,
you will not get water temperature and you will not be able to turn on
the LED or change the channel on the RSS™. You will still be able to
read digital depth and bottom contour information.
NOTE:
When using an RF40A or RF40B RSS™, make sure to select
the matching channel from the CHANNEL SELECT menu on the
Control Head.
Maintenance
Your SmartCast
®
is designed to provide years of
trouble-free operation with virtually no maintenance.
Follow these simple procedures to ensure your
SmartCast
®
continues to deliver top performance.
WARNING!
Never leave the RF25 SmartCast
®
product in a closed
car or trunk - the extremely high temperatures generated in hot
weather can damage the electronics.
Rod Mounted Display Maintenance:
If the Rod
Mounted Display comes into contact with salt spray,
wipe the affected surfaces with a cloth dampened
with fresh water. When cleaning the protective lens
on the display, use a chamois and non-abrasive, mild
cleaner. Do not wipe while dirt or grease is on the
lens. Be careful to avoid scratching the lens. Do not
use a chemical glass cleaner on the lens, as this may
cause it to crack.
Temperature of 50 Means Channel
is Set to A
Temperature of 55 Means Channel
is Set to B
Do not store the Rod Mounted Display on your fishing rod,
in direct sunlight, or in extreme temperatures. When you
are not fishing for extended periods, remove the rod
mount from the rod and store it in a dry, cool place such
as your tackle box, away from extreme temperatures and
ultraviolet light.
RSS™ Maintenance:
After using the RSS™ in salt
water, wipe the affected surfaces with a cloth dampened
with fresh water. The RSS™ Wet Switch™ pins must be
rinsed with fresh water after exposure to salt water to
prevent corrosion.
If your RSS™ remains out of the water for a long period
of time, it may take some time to wet it when returned to
the water. Small air bubbles can cling to the surface of the
RSS™ and interfere with proper operation. Wipe the face
of the RSS™ with a wet cloth to remove them.
Troubleshooting
Do not attempt to repair the RF25 Rod Mounted Display
or RSS™ yourself. There are no user serviceable parts
inside, and special tools and techniques are required for
assembly to ensure the waterproof integrity of the
housings. Repairs should be performed only by
authorized Humminbird
®
technicians.
Many requests for repair received by Humminbird
®
involve units that do not actually need repair. These units
are returned “no problem found.” If you have a problem
with your SmartCast
®
, use the following troubleshooting
guide before calling the Customer Resource Center or
sending your unit in for repair.
1. The SmartCast
®
loses signal.
If the SmartCast
®
is not able to get
an RF signal from the RSS™, the
display will stop updating (the screen
will freeze) and the RF25 SmartCast
®
screen will be displayed after several
seconds. Whenever reception is lost
or the RSS™ emerges from the water for more than a
few seconds, the RF25 SmartCast
®
screen will be
displayed until the RSS™ is placed back in the water
and reception is regained.
• The SmartCast
®
system is a line-of-sight wireless
product. If objects are placed between the RSS™ and
the Rod Mounted Display, the reception may be lost.
• The RF25 depth range is 2 to 120 feet (0.6 to 35
meters). Erratic readings may occur in water that is
shallower than 2 feet (0.6 m). In addition, because of
the nature of sonar, this product is not intended for
use in swimming pools or small enclosed bodies of
water.
• Reeling the RSS™ too fast can cause loss of signal
and the screen will freeze.
• Check the buoyant balance between the RSS™ and
your tackle; over 0.2 ounce (5.7 grams) will
submerge the RSS™, causing signal loss.
• The RF25 may not obtain its maximum RF distance of
150 feet (45 meters) unless the water is smooth.
Waves or chop may reduce the RF range significantly.
NOTE:
Retrieving the RSS™ too rapidly, or the repetitive rocking motion
of rough water, can result in loss or distortion of the bottom detail on the
display. For best bottom detail, perform a smooth and slow reel-in with
constant speed and the rod tip up (holding the rod tip low or using a
heavy line may cause the RSS™ to submerge and momentarily lose
radio contact). The RSS™ has a maximum transmit range of 150 feet
(45 meters). If the unit is cast or drifts more than 150 feet (45 meters)
away from the receiver, the signal may be inconsistent or lost.
2. Nothing happens when I turn the Rod Mounted
Display on.
Check the battery position and make sure that the
battery door is properly closed. Also, make sure that
you have removed the plastic strip that is in the battery
compartment when it is new.
If this doesn’t help, replace the battery. After replacing
the battery, if the unit still doesn’t power up, remove the
battery door again and re-install.
If sonar performance becomes weak (i.e., there
are bottom gaps or "0" depth readings) the
bottom of the RSS™ needs to be cleaned with
a drop or two of a 5 to 10 percent solution of
liquid dish-washing detergent and water. Use
approximately one tablespoon (15 ml)
detergent to 8 ounces (237 ml) of water to
remove oils from the face of the RSS™, then
wipe with a damp cloth.
3. When in very shallow water, I get gaps in the
bottom reading and inconsistent digital depth
indication.
The SmartCast
®
will work reliably in water 2 feet (0.6
meter) or deeper. The depth is measured from the
RSS™.
4. The display begins to fade out. Images are not as
sharp as normal.
Check the battery position and make sure that the
battery door is properly closed. Also, make sure that
you have removed the plastic strip that is located in the
battery compartment when it is new.
If this doesn’t help, replace the battery. After replacing
the battery, if the unit still has a faded display, remove
the battery door again and re-install.
5. The display shows many black dots at high
sensitivity settings.
You are seeing noise or interference caused by one of
several sources. Noise can be caused by other
electronic devices. Turn off any nearby electronics and
see if the problem goes away. Other sonar devices or
any electronic device operating in the 900 mHz range
(in the 400 mHz range for International versions) could
cause interference with your SmartCast
®
.
6. The display shows fluctuating depth readings
and excessive clutter, including vertical bars
that may be drawn on top of fish icons.
The SmartCast
®
system comes with the capability to
receive separate signals from a Channel A RSS™ or a
Channel B RSS™. Two A- or B-type RSS™ units used
simultaneously, as well as one A- and one B-type
RSS™ unit used simultaneously, can cause RF
interference between each other.
7. The display jumps and the bottom has an abrupt
change; sometimes a vertical line is missing or
a black line from top to bottom is displayed.
This display image jump is due to an automatic change
in depth. New returns graphed at a different scale will
not match up with the historic data already graphed at
a higher or lower scale. Vertical lines can also occur as
the radio signal from the RSS™ is lost and then
regained in rough water conditions.
Humminbird
®
6 Month Limited Warranty
We warrant the original retail purchaser that products
made by Humminbird
®
have been manufactured free
from defects in materials and workmanship. This
warranty is effective for 6 months from the date of
original retail purchase. Humminbird
®
products found
to be defective and covered by this warranty will be
replaced or repaired free of charge at Humminbird
®
option and returned to the customer freight prepaid.
Humminbird
®
sole responsibility under this warranty is
limited to the repair or replacement of a product that
has been deemed defective by Humminbird
®
.
Humminbird
®
is not responsible for charges connected
with the removal of such product or reinstallation of
replaced or repaired parts.
This warranty does not apply to a product that has
been:
• Improperly installed;
• Used in an installation other than that
recommended in the product installation and
operation instructions;
• Damaged or has failed because of an accident or
abnormal operation;
• Repaired or modified by entities other than
Humminbird
®
.
Please retain your original receipt as a proof of the
purchase date. This will be required for in-warranty
service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER
WARRANTIES, OBLIGATIONS OR LIABILITIES ON THE
PART OF HUMMINBIRD
®
AND WILL BE THE
CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY
APPLICABLE IMPLIED WARRANTIES UNDER STATE
LAW WHICH ARE HEREBY LIMITED IN DURATION TO SIX
MONTHS FROM THE DATE OF ORIGINAL PURCHASE. IN
NO EVENT WILL HUMMINBIRD
®
BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied
warranty,
or the exclusion of incidental or
consequential damages, so the above exclusions may
not apply to you. You may also have other rights, which
vary from state to state.
International Purchases
A separate warranty is provided by international
distributors for units purchased outside the United
States. This warranty is included by your local
distributor and this distributor maintains local service
for your unit. Warranties are only valid in the area of
intended distribution. Units purchased in the United
States or Canada must be returned to our factory in
the United States for service.
Humminbird
®
Service Policy
Even though you'll probably never need to take
advantage of our incredible service policy, it's good to
know that we back our products this confidently. We
do it because you deserve the best. We will make
every effort to repair your unit within three business
days from the receipt of your unit at our factory. This
does not include shipping time to and from our factory.
Units received on Friday are typically shipped by the
following Wednesday, units received Monday are
typically shipped by Thursday, etc.
All repair work is performed by factory-trained
technicians to meet exacting factory specifications.
Factory-serviced units go through the same rigorous
testing and quality control inspections as new
production units.
After the original warranty period, a standard flat rate
service charge will be assessed for each repair
(physical damage and missing parts are not included).
Any repairs made after the original warranty will be
warranted for an additional 90 days after service has
been performed by our factory technicians. You can
contact our Customer Resource Center or visit our
website to verify the flat rate repair fee for your
product (visit the Product Support section):
http://www.humminbird.com
We reserve the right to deem any product
unserviceable when replacement parts are no longer
available or impossible to obtain. This Service Policy is
valid in the United States only. This applies only to
Humminbird
®
products returned to our factory in
Eufaula, Alabama. This Service Policy is subject to
change without notice.
Returning Your Unit for Service
Before sending your unit in for repair, please contact
the factory, either by phone or by email, to obtain a
Repair Authorization Number for your unit.
Please
have your product model name and serial number
available before calling the factory. If you contact the
factory by e-mail, please include your product model
name and serial number in the e-mail, and use
Request for Repair Authorization Number for your e-
mail subject header. You should include your
Repair Authorization Number in all subsequent
communications about your unit.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the
Humminbird
®
Customer Resource Center.
• Tag product with your customer name, street
address, phone number and your assigned Repair
Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and
date of purchase).
• Return product freight prepaid to Humminbird
®
,
using an insured carrier with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the
Humminbird
®
Customer Resource Center.
• Include payment in the form of credit card number
and expiration date, money order or personal
check. Please do not send cash.
• Tag product with your customer name, street
address, phone number and your assigned Repair
Authorization Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird
®
,
using an insured carrier with delivery confirmation.
S P E C I F I C A T I O N S
Rod Mounted Display Specifications:
Power Requirement ....................One 2450 CR Battery
Display Matrix ......................................48 X 32 Pixels
Display Type ........................................................ STN
RSS
™
Specifications:
Power Requirement ....................One non-replaceable
Lithium RSS
TM
Battery
Battery Expected Life ........ 3 years (approximately 500
hours of in-water use)
Depth Capability .......... 2 - 120 feet (0.6 - 35 meters)
Sonar Coverage .................................. 90° @-10 dB*
Sonar Operating Frequency .......................... 125 kHz
Operational Radio Frequency .................... 916.5 mHz
(433.92 mHz International)
Operational Range ...................... 150 feet (45 meters)
* Area of bottom coverage equals twice the current depth.
Contact Humminbird
®
Your Humminbird
®
accessory is designed for trouble-free operation
and is backed by a six-month warranty.
If you have any questions, contact our
Humminbird
®
Customer Resource Center
:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
For direct shipping, our address is:
Humminbird
Service Department
108 Maple Lane
Eufaula, AL 36027 USA
Humminbird
®
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference and;
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION
: Changes or modifications not expressly approved by
Humminbird
®
could void the user’s authority to operate the device.
FCC ID: ICLSMC1
