Humboldt h-4169 Скачать руководство пользователя | Manualshive

Страница: 8 / 8

background image

www.humboldtmfg.com

HUMBOLDT

Testing Equipment for

Construction Materials

Humboldt Mfg. Co.

875 Tollgate Road

Elgin Illinois 60123 U.S.A.

U.S.A. Toll Free: 1.800.544.7220

Voice: 1.708.456.6300

Fax: 1.708.456.0137

Email: [email protected]

Supplied By:

Warranty

Humboldt Mfg. Co. warrants its products to be free from defects in material or

workmanship. The exclusive remedy for this warranty is Humboldt Mfg. Co.,

factory replacement of any part or parts of such product, for the warranty of this

product please refer to Humboldt Mfg. Co. catalog on Terms and Conditions

of Sale. The purchaser is responsible for the transportation charges. Humboldt

Mfg. Co. shall not be responsible under this warranty if the goods have been

improperly maintained, installed, operated or the goods have been altered or

modified so as to adversely affect the operation, use performance or durability

or so as to change their intended use. The Humboldt Mfg. Co. liability under

the warranty contained in this clause is limited to the repair or replacement of

defective goods and making good, defective workmanship.

«
...
6
7
8

Содержание h-4169









Отзывы:

Нет отзывов

Похожие инструкции для h-4169

WasteGuard KWD100-100MBL

Бренд: Kraus Страницы: 17

Бренд: Power Craft Страницы: 67

Бренд: Chicago Pneumatic Страницы: 36

Бренд: PAIFANG Страницы: 11

Бренд: ORKEL Страницы: 137

Бренд: EcoFast Страницы: 52

Бренд: Mikasa Страницы: 32

Бренд: Mikasa Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды