HumanLab DMF-05 Скачать руководство пользователя

Страница: 3 / 18

-3-

•

Safety warnings

A risk of electric shock exists.

Make sure to install a ground wire.

Electric shock may occur without a ground

wire installation.

Fire or burns may occur.

Do not place objects near the ceramic blocks.

These blocks are very hot after operation.

Explosion or fire may occur due to improper handling.

Do not put flammable, explosive materials in the oven.

Before operating, read and understand safety warnings thoroughly

and use this equipment properly.

Keep these warnings in mind for your safety.

Safety Warnings: Danger!,Warning!,Caution!

Danger : Failure to observe this instruction can result in a

personal injury or death.

Warning : Failure to observe this instruction may cause a fatal

injury

Caution : Violation of this instruction and improper use may

cause a serious injury and property damage.

Electric shock may occur.

Unplug the power before you open the covers.

Caution

Warning

Danger

Warning

MUFFLE FURNACE

Содержание DMF-05



















Результаты поиска

Содержание DMF-05

Отзывы:

Похожие инструкции для DMF-05

Бренды по названию

Популярные бренды

HumanLab DMF-05, Руководство по эксплуатации

Результаты поиска

Содержание DMF-05

Отзывы:

Похожие инструкции для DMF-05

Бренды по названию

Популярные бренды