Hughes HughesNet Ka-band Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

Hughes HughesNet Ka-band Скачать руководство пользователя страница 25

Chapter 2 • Pointing the antenna

1037663-0001 Revision A

17

4. When the signals are peaked, tighten the azimuth and

elevation bolts completely, then loosen the bolts just enough
so that you can adjust the azimuth and elevation with the fine
azimuth and elevation pointing tools. By tightening the bolts
to this level, you can avoid any unwanted movement during
antenna lockdown.

Fine pointing

Fine pointing or

dithering

is the process of more accurately

pointing the antenna at the satellite. During this phase, the
squinter and fine az/el mechanism are used to finely align the
antenna and lock it down. The squinter, which blocks off one half
of the feed horn, is placed alternately in four different positions
on the feed horn, two for measuring azimuth and two for
measuring elevation. When the antenna is pointed correctly, the
SQF readings at the two azimuth positions will match, and the
readings at the two elevation positions will match.

The following steps describe the fine-pointing process.

1. Place the appropriate squinter for the antenna on the feed

horn. Refer to Table 3 below to determine which squinter you
should use, then follow the appropriate procedure.

Table 3: Determining which squinter to use

Antenna

Squinter

Type

Hughes

Part Number

Prodelin

.74m antenna

(elliptical feedhorn)

A

1501447

Prodelin

.98m, 1.2m, or 1.8m
antenna

(circular feedhorn)

B

1501454

Raven .74m or .98m
antenna

(circular feedhorn)

C

1501451

Note:

Squinters are available in three sizes to accommodate

all of the antenna dish sizes. Be sure to use the correct
squinter for the antenna as listed in Table 3.

«
...
23
24
25
26
27
...
»

Содержание HughesNet Ka-band













































Отзывы:

Нет отзывов