Hughes HN9400 Скачать руководство пользователя страница 89

Страница: 89 / 134

Figure 64: System Information page

The parameters listed in the

HN9400 Info

section of the System Information page are explained

in the following table. Other sections of the screen (

Transmit Radio Info

and

Satellite

) provide

additional information about the router installation and the router software (

Software

Configuration

Table 9: System Information page parameters – HN9400 Info section

Explanation

Parameter

Identifies the site where the router is installed.

Site ID

The router’s serial number. The serial number may be required for
troubleshooting.

Serial number

ZIP code of the router site.

Zipcode

Software build date.

Software Date

Version of the router’s software. This is typically the factory-installed
software version. However, if the NOC downloads a newer version

Software Release

of Gateway software to the router, the newer version number is
displayed.

The satellite router address. The default router address is
192.168.0.1. A different router address can be configured.

LAN1 IP Address

Range of addresses available to the satellite router.

LAN1 Subnet Mask

MAC address for the satellite router.

LAN1 MAC Address

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Chapter 6

System Control Center

Содержание HN9400







































































































































Результаты поиска

Содержание HN9400

Отзывы:

Похожие инструкции для HN9400

Бренды по названию

Популярные бренды

Hughes HN9400, Руководство по установке

Результаты поиска

Содержание HN9400

Отзывы:

Похожие инструкции для HN9400

Бренды по названию

Популярные бренды