Hughes DIRECWAY DW7000 страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 98

background image

Chapter 4 • Troubleshooting

1035978-0001 Revision A

31

Confirming TCP

acceleration is operational

Transmission Control Protocol (TCP) Acceleration is a
proprietary protocol provided by DIRECWAY. It optimizes
performance for TCP and Internet Protocol (IP)-based
applications, including faster downloads over satellite.

1. At the System Control Center, click on the System Status

indicator. The System Status page appears. See Figure 21.

2. Check the message in the

TCP Acceleration Status

row.

If the message says

Operational

, TCP Acceleration is

enabled. Proceed to the next troubleshooting step.
If the message says

Not Operational

, TCP Acceleration is

disabled. Perform the following steps:
a. Check that receiving and transmitting are working. If they

are not, troubleshoot them as per the previous two sections.

b. If receiving and transmitting are working but TCP

Acceleration is still not operational, power cycle the
terminal by unplugging the power cord from the power
source, waiting 10 seconds, and plugging it back in. Check
the TCP Acceleration status again. If it is not operational,
or operational but you still cannot surf the Internet,
proceed to the next troubleshooting step.

c. If TCP Acceleration is still disabled after power cycling,

contact customer support for assistance.

Figure 21: Confirming TCP acceleration is operational

«
...
43
44
45
46
47
...
»

Содержание DIRECWAY DW7000



































































































Отзывы:

Нет отзывов

Похожие инструкции для DIRECWAY DW7000

Бренд: GE Страницы: 107

Бренд: Icom Страницы: 26

MorphoAccess VP Series

Бренд: Safran Страницы: 126

Бренд: VeriFone Страницы: 6

Бренд: Mitsubishi Electric Страницы: 26

Бренд: Mitsubishi Electric Страницы: 6

Бренд: Mitsubishi Electric Страницы: 6

Lossnay PZ-4GS-E

Бренд: Mitsubishi Electric Страницы: 4

Бренд: Mitsubishi Electric Страницы: 13

Бренд: Burnside Страницы: 2

Бренд: Datavan Страницы: 42

Бренд: National Instruments Страницы: 12

Бренд: PAX Страницы: 6

Бренд: Russound Страницы: 2

Бренд: ABB Страницы: 110

Бренд: Quest Engineering Страницы: 11

Бренд: UTC RETAIL Страницы: 16

Бренд: Wasp Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды