Hughes DIRECWAY DW7000 Скачать руководство пользователя

Страница: 32 / 98

Chapter 2 • System Control Center

1035978-0001 Revision A

Connectivity Test page

The Connectivity Test page has a link that can be used to test the
DW7000’s connectivity to the NOC.

See Chapter 4 – Troubleshooting for instructions explaining how
to access and perform the test.

Port Forwarding
Configuration page

The Port Forwarding page shown in Figure 12 may be used to
define rules for allowing TCP and UDP traffic on the Internet to
access servers on your network.

Defining port forwarding

rules

Follow these steps to use the Port Forwarding Configuration page
to define port forwarding rules:

1. Open a web browser on a computer connected to the

DW7700.
You may also use a computer on the LAN if the DW7700 is
connected to an Ethernet device, such as a hub or router.

2. Type

www.systemcontrolcenter.com

in the browser’s

location or address bar and press E

NTER

3. Click

Port Forwarding Configuration

on the System

Control Center home page or in the left frame of the page you
are currently on.

4. Click Add Rule on the Port Forwarding Configuration page.

See Figure 12.

Figure 12: Port Forwarding Configuration page

Содержание DIRECWAY DW7000



































































































Результаты поиска

Содержание DIRECWAY DW7000

Отзывы:

Похожие инструкции для DIRECWAY DW7000

Бренды по названию

Популярные бренды

Hughes DIRECWAY DW7000, Руководство пользователя

Результаты поиска

Содержание DIRECWAY DW7000

Отзывы:

Похожие инструкции для DIRECWAY DW7000

Бренды по названию

Популярные бренды