Hughes DIRECWAY DW7000 Скачать руководство пользователя | Manualshive

Страница: 21 / 98

background image

Chapter 2 • System Control Center

1035978-0001 Revision A

7

Chapter 2

System Control Center

The System Control Center is a web interface that provides
access to important system information, configuration
parameters, documentation, and help topics. Access the System
Control Center by opening a web browser on a computer
connected to the terminal and browsing to

www.systemcontrolcenter.com

.

The DW7700 also has a System Control Center, which is
described in the DW7700 Supplemental User Guide
(1036332-0001). The DW7700 is an enterprise-class broadband
communications solution used by enterprise customers, which are
typically large businesses.

This chapter discusses the following System Control Center
topics:

•

Accessing the System Control Center on page 8

•

Home page on page 10

•

System Status page on page 13

•

Reception Information page on page 14

•

Transmission Information page on page 15

•

System Information page on page 16

•

Connectivity Test page on page 18

•

Port Forwarding Configuration page on page 18

•

Help page on page 19

•

myDIRECWAY on page 21

Note:

Each terminal’s software is updated periodically over the

satellite link. Always refer to the System Control Center’s Help
page for current information about the System Control Center and
the terminal’s software.

«
...
19
20
21
22
23
...
»

Содержание DIRECWAY DW7000



































































































Отзывы:

Нет отзывов

Похожие инструкции для DIRECWAY DW7000

Бренд: Omni Страницы: 2

Бренд: Moneris Страницы: 86

Бренд: Network Computing Devices Страницы: 45

Бренд: Heathkit Страницы: 96

Бренд: Dormakaba Страницы: 103

Бренд: XAC Страницы: 6

Pro-face GLC2300

Бренд: Digital Electronics Corporation Страницы: 155

Бренд: SkyWave Страницы: 64

VoloAccess VA100 Series

Бренд: Vololink Страницы: 2

Бренд: LACROIX Sofrel Страницы: 26

Бренд: Transax Страницы: 8

Бренд: Transax Страницы: 12

Бренд: Opticon Страницы: 36

POStation 7000 Series

Бренд: Fametech Страницы: 16

Бренд: Fancom Страницы: 25

Бренд: PAR Страницы: 14

Бренд: Nokia Страницы: 3

Бренд: Nokia Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды