background image

 

Installation Manual 3000B

 

 

Page 6 of 9 

May 2012 

 

 

COMPLETE SEVERE DUTY RETAIN-
ER (SDR) INSTALLATION (OPTIONAL 
EQUIPMENT) 
 

If  the  SDR  is  installed,  the  blade  socket  jam  nuts  &  blade 
socket  cap  screws  (labeled  1 and  2  in  Figure  5B,  5C)  must 
now be finally tightened to the recommended standard of 15 
ft-lbs (lubricated) or 20 ft-lbs (dry) and the SDR cap screws 
(labeled 3 in Figure 5B, 5C) must now be finally tightened to 
20 ft-lbs (lubricated) or 25 ft-lbs (dry). 

 
 

FINAL INSTALLATION CHECK 
(IMPORTANT) 
 

Double check and make final adjustments as necessary by 
essentially going through the provisions of those paragraphs 
entitled “

Blade Installation” 

on page 3 through “

Complete 

Severe Duty Retainer Installation” 

on page 6 inclusively. 

 
In so doing, one shall check the following setup criteria for 
all blade positions:  
 
0.    Blade seated in hub socket. 
1.  Retainer rings fully seated in blade neck grooves and 

hub socket grooves. 

2.  If applicable, SDR’s properly mounted into hub sockets 

and onto blade necks. 

3.  Blade pitch set /-0.2 degrees of design value. 
4.  Tracking, if possible (see note above), set /-0.3 

75” (3/4” max spread). 

5.  All (4 per blade pos) blade retainer cap screws torqued 

to spec, 15 ft-lbs (lubricated) or 20 ft-lbs (dry). 

6.  All (4 per blade pos) blade retainer cap screws jam nuts 

torqued to spec, 15 ft-lbs (lubricated) or 20 ft-lbs (dry). 

7.  If applicable, SDR cap screws torqued to spec, 20 ft-lbs, 

(lubricated) or 25 ft-lbs (dry). 

SEAL DISC INSTALLATION

  

 
Fasten  seal  disc  to  top  of  hub  with  four  (4)  3/8”  cap  screws, 
placing  flat  washers  between  seal  disc  and  lock  washer  (See 
Figure  8).  Tighten  to  recommended  standard  of  15  ft-lb 
(lubricated) or 20 ft-lb (dry). 

CHECKING TIP CLEARANCE 

 

Rotate fan in position inside fan ring or fan stack to check tip 
clearance  (See  Figure  9).  The  recommended  tip  clearance  is 
between  1/2”  and  1”.  Check  for  spots  where  fan  blade  clear-
ance is not within the recommended tolerance. 

Fan Diameter (ft)

 

Minimum

 

Maximum

 

6’ through 9’

 

1/4”

 

1/2”

 

>9’ through 11’

 

1/4”

 

5/8”

 

>11’ through 14’

 

1/4”

 

3/4”

 

TIP CLEARANCE 

Figure 8 

Figure 9 

Содержание Tuf-Lite 3000B Series










Отзывы: