manualshive.com logo in svg

Hudson River Stove Works DAVENPORT, Руководство пользователя / Инструкция по установке

Поделиться
Скачать
Hudson River Stove Works DAVENPORT Скачать руководство пользователя страница 18

A  noncombustible  hearth  pad 

must  cover  combustible  flooring 

underneath, as well as 9” in front of 

the heater and 6” to the side of the 

heater

1. Install the hearth pad.
2. Lock  the  fireplace  damper  in  the 

open position.

3. Install a positive flue connector at 

the fireplace damper.

4. Connect a tee or 90° degree elbow 

to the exhaust pipe.

5. This  fireplace  insert  must  be 

installed  with  a  continuous 

chimney liner of 3 or 4” diameter 

extending  from  the  fireplace 

insert  to  the  top  of  the  chimney.  

The liner must conform to type 3 

requirements of CAN/ULC S635.

6. (Recommended)  Install  fresh  air 

intake  either  through  the  back 

of  the  fireplace  or  through  the 

positive flue connector.

When  installing  the  insert  into  a 
masonry  fireplace  DO  NOT  remove  any  bricks  or  masonry,  with  the  following  exception;  masonry  or 

steel, including the damper plate, may be removed from the smoke shelf and adjacent damper frame if 

necessary to accommodate a chimney liner.  Provided that their removal will not weaken the structure 

of the fireplace and chimney, and will not reduce protection for combustible materials to less than that 

required by the national building code.

When installing the fireplace insert into a zero clearance fireplace, 

DO NOT

 cut or modify any factory 

firebox parts.  If the fireplace insert does not fit into a zero clearance fireplace we recommend you use 

an ENVIRO freestanding model and install as a hearth mounted unit. 

 

Install a 3” (76 mm) flex pipe from 

the stove to the top of the chimney (see “

i

nstallation

 - h

earth

 m

ount

 i

nstallation

 - f

reestanding

”).

Installation

m

aSonRy

 f

iRePLace

 i

nSeRt

 i

nStaLLation

 - f

iRePLace

 i

nSeRt

:

The Fireplace insert model requires a surround faceplate and a pedestal. When installing this unit, ensure 

that the pedestal is removed from the inside of the hopper and installed on the bottom of the unit (Refer 

to 

i

nstallation

 - i

nstallation

 

of

 p

edestal

 

and

 l

eveling

 l

egs

 - f

ireplace

 i

nsert

).  

Adjust hopper height (see 

i

nstallation

 - i

nstalling

 h

opper

 c

over

 

and

 a

djusting

 h

opper

 h

eight

 - f

ireplace

 i

nsert

) 

and assemble surround panel (see Installation - 

i

nstallation

 

and

 r

emoval

 

of

 c

ontrol

 p

anel

 

in

 t

he

 s

urround

 

p

anel

 - f

ireplace

 i

nsert

 and Installation - 

a

ssembly

 

and

 i

nstallation

 

of

 i

nsert

 s

urround

 p

anels

 - f

ireplace

 i

nsert

) 

before starting installation.

Figure 21: Installation of Fireplace Insert. 

18

Floor

Protection

Combustible Floor

Masonry Fireplace

Min 9" 

Rain Cap

Steel Plate or Flashing

Flexible or Rigid 6"

Stainless Steel Liner

Mantel

Minimum 8" (20 cm) 

from top of stove

Surround Panel

Fresh-air intake

Clean-out tee

If holes already exist 

fresh-air intake can 

be taken through the 

back of the fireplace 

or through the ash 

dump.

Flexible stainless

steel pipe connection

Damper Removed

or Fastened Open

Содержание DAVENPORT







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды