manualshive.com logo in svg

Huck LH-224, Инструкция по эксплуатации

Поделиться
Скачать
Huck LH-224 Скачать руководство пользователя страница 11

Instructions for use

1. Read and ensure that you understand

the Safety Guidelines at the front of this

manual. Also, read and ensure that you

understand the Specification, Noise,

Vibration and  Principal of Operation

information shown on page 4.

2. Ensure that the hole in the material to

be joined is prepared in accordance with

the information shown on the Engineering

Standards for the fastener being installed.

3. Ensure that the grip length of the

fastener to be installed is correct for the

material thickness to be joined, (refer to

the appropriate Engineering Standards for

the fastener being used).

4. Ensure that the equipment has been

prepared for use, (refer to the section in

this manual "Preparation for Use").

W ARNING

DO NOT OPERATE TOOLS WITHOUT

PINTAIL DEFLECTORS. UNSHIELDED

EYES, ESPECIALLY, MAY BE

P E R M A N T LY INJURED AND OTHER

SEVERE INJURIES MAY BE CAUSED

BY FLYING PINTAILS. WHEN A

DEFLECTOR IS IN PLACE ON THE

TOOL, BROKEN PINTAILS WILL STILL

EJECT WITH SPEED AND FORCE.  BE

SURE THE PINTAIL DEFLECTOR IS

DIRECTED SAFELY.

5. Insert the fastener into the prepared

hole.

6. Hold the Installation Tool firmly by the

handle with the hand in a position that

enables finger operation of the Air Trigger.

If necessary, use the other hand to

support the Installation Tool by holding the

Air Cylinder of the tool. D O N O T place the

hand arround the Nose Assembly. If a

Pintail Collector Bottle or Bag is not fitted

to the Installation Tool, ensure the

Deflector is positioned safely so that the

ejected Pintails will not cause injury to 

yourself or fellow workers.

8

7. Place the Nose Assembly over the

Pintail of the fastener and gently push

forward until the Anvil of the Nose

Assembly is in contact with the fastener.

Operate the Air Trigger.

8. When the fastener Pintail fractures, (at

the same time the Installation Tool may be

released from the installed fastener),

release the Trigger. The Installation Tool

Piston and inner components of the Nose

Assembly will now return to the fully

forward position, (return stroke),  ready to

install the next fastener; this normally 

takes about one second.

To avoid damage to the Nose Assembly,

DO NOT place the Nose Assembly over

the Pintail of a fastener until the return

stroke is completed.

9. If a Pintail Collector Bottle or Bag is

fitted to the Installation Tool, empty at

regular intervals using authorised disposal

proceedures.

Failure to do this will could result in

Pintails causing a blockage in the

Installation Tool and/or  Nose Assembly

resulting in serious damage to

components. 

10. In the event of a mains air supply

failure coincident with a fastener retained

in the Nose Assembly of the Installation

Tool, the Installation Tool and Nose

Assembly must be placed in a safe

location to prevent inadvertent operation

of the Trigger once power is restored.

Содержание LH-224



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды