LED ON = OK
Figure 3: Diagnostic Operation
Figure 4: Dimensions
3.75
[95]
3.60
[91]
3.00
[76]
0.87
[22]
2.67
[68]
Dimensions:
in.
[mm]
Single-phase 3-wire
(+GND) 120/240 Vac
0.5 in. [13 mm] knockout (trade size)
Actual hole size 0.875 in. [22 mm]
an accessible location (not within walls).
1. Turn off all power supplying this equipment before working on or
inside equipment.
2. For mounting, see Figure 1.
3. Confirm SPD is rated for your system by comparing voltage
measurements to the Line Voltage (L-L, L-N) on the product label.
4. Confirm the black wires are connected to line wires, the white wire
to the neutral wire and green wire to ground (see figure 2). For the
5. Twist conductors 1/2 turn or more for every 12 inches of length.
6. Keep conductor length as short as possible with no sharp bends.
7. Do not loop or coil wires.
8. Use on solidly grounded systems only.
General Specifications
Short Circuit Current Rating
25 kA
I
Enclosure Rating
Type 4X
Product Weight
1.8 lbs (0.9kg)
Connection Method
Parallel, #12 AWG Solid Wire
Thermal Fusing
Yes
Operating Temperature
-40° to +160° F (-40° to +70° C)
Operating Frequency
50/60 Hz
Diagnostics
Green Status LED per line
Product Standards
UL 1449-3rd Edition, CSA C22.2 No. 8-M1986,
Figure 1: Mounting Unit
Single-phase 2-wire
(+GND) 120 Vac
INSTALLATION
VPR
700V L1-N, 700V L1-G, 700V L2-N, 800V L2-G
System Voltage
120/240VAC
MCOV
150VAC
Product Rating
Type 1 SPD
(n)
CSA C233.1-87 and CE
Nut
NOTE: The Surge Protective Device must be installed in
Black
Green
Black
White
L1
N
L2
Green
Black
White
L
N
LED ON = Normal Operation
LED OFF = Check breakers and connections.
Verify line voltage at point of SPD connection;
Iif all correct replace SPD
Panel
0.5 in. [13 mm] knockout (trade size)
Actual hole size 0.875 in. [22 mm]
single-phase, 120/240V 3-wire application, connect one of the SPD
black wires to L1 and the other black wire to L2. For the single-
phase, 120V 2-wire application, connect both SPD black wires
to the same line.
Figure 2 : Wiring Diagrams
LED OFF = Fault,
L1 and/or L2
1. Suitable for use on a circuit capable of delivering not more than 25 kA rms symmetrical Amperes.
2. Contains no serviceable parts.
10kA (L1-N, L1-G, L2-N, L2-G)
Models
Voltage
Mounting
HBL3W120
Side Nipple
120/240
Side Nipple
HBL3W50
Surge + Overvoltage
Protection
Surge + Overvoltage
Max Surge
Current
120kA
50kA
120/240
2
Hubbell Modular Panel Surge Protective Device (SPD)
Hubbell Hardwired Surge Protective Device (SPD)
INSTAllATION
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Hubbell for any consequences arising out of the use of this material.
Hubbell Wiring Devices
1-800-729-3406 | www.Hubbell-Wiring.com
