Hubbell Geyser-RO Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 27

background image

22

FREQUENTLY ASKED QUESTIONS / TROUBLESHOOTING

The following are a sequence of lights and are used for assuring the proper function of the

Geyser-RO

and to help diagnose the unit if a problem occurs.

On/Off Button

Green

Power is on and unit is in standby.

Green service light

Solid Green

Unit is producing hot water.

Amber light is on

Solid Amber

Unit is in the defrost cycle.

Red light is on

Solid Red

Unit is in over current. Push the red reset button
next to the power switch. The Geyser will now
operate normally. (There may be a 5 minute delay
in starting). If the situation persists, turn the
Geyser off and call for service. Call technical
support at

Hubbell

.

203-378-2659

.

«
...
20
21
22
23
24
...
»

Содержание Geyser-RO




























Отзывы:

Нет отзывов

Похожие инструкции для Geyser-RO

Бренд: X-POWER Страницы: 44

Бренд: iGenix Страницы: 6

Бренд: EBARA Страницы: 22

Бренд: VARISCO Страницы: 72

Бренд: Rinnai Страницы: 20

BLACKLIGHT 7815

Бренд: MO-EL Страницы: 12

NEXIS-VE Series

Бренд: salmson Страницы: 120

Бренд: Waterax Страницы: 5

Бренд: Binks Страницы: 40

Бренд: Barnstead Thermolyne Corporation Страницы: 32

Бренд: Tallas Pumps Страницы: 21

Бренд: Enapter Страницы: 2

Krystal Clear CS7221

Бренд: Intex Страницы: 33

Бренд: Goldair Страницы: 4

Бренд: Lasko Страницы: 6

Бренд: Oase Страницы: 52

Бренд: Nacecare Страницы: 8

Бренд: Trillium Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды