Hubbell BWXSS-3775 Скачать руководство пользователя страница 31

D

O IT

O

NCE

. D

O IT

R

IGHT

.

TACO, INC.

, 1160 Cranston Street, Cranston, RI 02920

Telephone: (401) 942-8000

FAX: (401) 942-2360.

TACO (Canada), Ltd.

, 6180 Ordan Drive, Mississauga, Ontario L5T 2B3.

Telephone: 905/564-9422.

FAX: 905/564-9436.

Visit our web site at: 

http://www.taco-hvac.com

Printed in USA

Copyright 2004

TACO, Inc.

REPLACING MOTOR ASSEMBLY:

1. Disconnect the electrical supply.
2. Reduce system pressure to 0 psi and allow system to return to room temperature. Isolate the circulator by closing the

service valves or draining the system.

3. Remove the body bolts and swing motor assembly away from the body.
4. Install new motor, and reassemble circulator using the new gasket and bolts supplied.
5. Follow the “installation” procedure to start up the circulator.

REPLACING CARTRIDGE ASSEMBLY:

1. Disconnect the electrical supply.
2. Reduce system pressure to 0 psi and allow system to return to room temperature. Isolate the circulator by closing the

service valves or draining the system.

3. Remove the body bolts and swing motor assembly away from the body.
4. Pull cartridge out of the motor housing.
5. Install replacement cartridge, making sure that the cover plate is between the cartridge flange and motor.
6. Make sure the replacement cartridge corresponds to the full circulator product number. A complete parts list is avail-

able from your local plumbing supply wholesaler.

7. Reassemble the circulator using the new gasket and bolts supplied.
8. Follow the “Installation” procedure to start up the circulator.

REPLACING CAPACITOR:

1. Replacement capacitor must have same rating as originally furnished.

Taco, Inc. will repair or replace without charge
(at the company’s option) any product or part
which is proven defective under normal use
within one (1) year from the date of start-up or
one (1) year and six (6) months from date of
shipment (whichever occurs first).

Taco, Inc. will repair or replace without charge
(at the company’s option) any Taco 00 Series
circulator cartridge that is proven defective
under normal use within three (3) years from the
date of start-up or three (3) years and six (6)
months from date of shipment (whichever
occurs first).

In order to obtain service under this warranty, it
is the responsibility of the purchaser to prompt-
ly notify the local Taco stocking distributor or
Taco in writing and promptly deliver the subject
product or part, delivery prepaid, to the stocking
distributor. For assistance on warranty returns,
the purchaser may either contact the local Taco
stocking distributor or Taco. If the subject prod-
uct or part contains no defect as covered in this
warranty, the purchaser will be billed for parts

and labor charges in effect at time of factory
examination and repair.

Any Taco product or part not installed or operat-
ed in conformity with Taco instructions or which
has been subject to misuse, misapplication, the
addition of petroleum-based fluids or certain
chemical additives to the systems, or other
abuse, will not be covered by this warranty.

If in doubt as to whether a particular substance
is suitable for use with a Taco product or part, or
for any application restrictions, consult the
applicable Taco instruction sheets or contact
Taco at [401-942-8000].

Taco reserves the right to provide replacement
products and parts which are substantially sim-
ilar in design and functionally equivalent to the
defective product or part. Taco reserves the
right to make changes in details of design, con-
struction, or arrangement of materials of its
products without notification.

TACO OFFERS THIS WARRANTY IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. ANY

WARRANTY IMPLIED BY LAW INCLUDING
WARRANTIES OF MERCHANTABILITY OR
FITNESS IS IN EFFECT ONLY FOR THE DURA-
TION OF THE EXPRESS WARRANTY SET
FORTH IN THE FIRST PARAGRAPH ABOVE.

THE ABOVE WARRANTIES ARE IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR
STATUTORY, OR ANY OTHER WARRANTY
OBLIGATION ON THE PART OF TACO.

TACO WILL NOT BE LIABLE FOR ANY SPE-
CIAL, INCIDENTAL, INDIRECT OR CONSE-
QUENTIAL DAMAGES RESULTING FROM THE
USE OF ITS PRODUCTS OR ANY INCIDENTAL
COSTS OF REMOVING OR REPLACING
DEFECTIVE PRODUCTS.

This warranty gives the purchaser specific
rights, and the purchaser may have other rights
which vary from state to state. Some states do
not allow limitations on how long an implied
warranty lasts or on the exclusion of incidental
or consequential damages, so these limitations
or exclusions may not apply to you.

LIMITED WARRANTY STATEMENT

Содержание BWXSS-3775








































Отзывы: