Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 67

Страница: 67 / 175

●

Reserve a clearance of at least 950 mm from the front of the cabinet for

ventilation and operations.

●

Reserve a clearance of at least 500 mm from the top of the cabinet for

operations.

●

Reserve a clearance of at least 500 mm from the rear of the cabinet for

ventilation.

●

Reserve a clearance of at least 800 mm if you need to perform operations at

the rear of the cabinet.

6.1.3 Tools and Instruments

NO TICE

● Use insulated tools to avoid electric shocks.
● The following table lists only the common tools for installation and cable

connection. For more dedicated tools required, see the document for each

component. Prepare tools based on site requirements.

Table 6-1 Tools and instruments

Tools and Instruments

Electric forklift

Manual forklift

Step ladder

Rubber mallet

Hammer drill (with a

Φ16 drill bit)

Hand-held electric drill

Hole saw

Heat gun

Diagonal pliers

Crimping tool

Wire strippers

Electro-hydraulic

pliers

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

6 Installation

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды