manualshive.com logo in svg

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 45 / 158

Поделиться
Скачать
Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 45

UPS2000-G-(3 kVA-20 kVA)-V2 
User Manual (Two Live Wires) 

3 Installation 

 

Issue 07 (2019-12-19) 

Copyright © Huawei Technologies Co., Ltd. 

38 

 

Step 2

 

Move the UPS to the installation position. 

Step 3

 

Unpack the case. 

Step 4

 

Check the UPS packing. 

1.

 

Check the UPS bar code (which is at the rear panel of the UPS, near the air exhaust vent), 
and ensure that it complies with the order. 

2.

 

If there is any discrepancy, contact your local Huawei office immediately. 

----End 

3.2 Installation Procedure 

UPS installation includes mechanical installation and cable connection. Installation modes 
include tower installation and rack installation. You can select an installation mode based on 
the site requirements. 

3.3 Installing a Backfeed Protection Device 

 

 

The UPS has no built-in backfeed protection device. You can install a backfeed protection 
device on the input front side. 

If you do no install a backfeed protection device on the input front side, attach a warning label 
to the main power isolation device. The label reads like this: "This circuit supplies power to 
the UPS. Before cable connection, disconnect the UPS, and check the voltage across wiring 
terminals." 

When battery mode is unavailable or the mains fails, the UPS internal voltages or energy may 
flow back directly, or through a leakage path, to an input terminal. To minimize the risk of 
electric shocks, install a backfeed protection device on the input side. 

Table 3-3

 lists the rated voltages and currents for backfeed protection contactors on the UPSs. 

Table 3-3

 

Rated voltages and currents for backfeed protection contactors 

Model 

Single-phase/three-phase 

Two live wires 

Rated Voltage 
and Current 

Recommended 
Contactor 
Models 
(Schneider 
contactors) 

Rated 
Voltage and 
Current 

Recommend
ed Contactor 
Models 
(ABB 
contactors) 

UPS2000-
G-3KRTL-
V2 

220 V AC, 230 V 
AC, 240 V AC, 17 
A 

LC1-D40A 

208 V AC, 
220 V AC, 17 
A 

AF50-30-11*
70 

UPS2000-
G-6KRTL-

220 V AC, 230 V 
AC, 240 V AC, 40 

LC1-D40A 

208 V AC, 
220 V AC, 40 

AF50-30-11*

Содержание UPS2000-G-10KRTLV2































































































































































Отзывы:

Нет отзывов