Huawei TP48200A-DX08A1 Скачать руководство пользователя страница 56

Страница: 56 / 73

TP48200A-DX08A1 and TP48200A-DX08A2 Telecom
Power
User Manual

4 Maintenance

Issue 06 (2019-11-15)

4.4.5 Replacing an AC SPD Module

Prerequisites



An ESD wrist strap, ESD gloves, ESD box or bag, and cabinet door key are available.



The new AC SPD module is intact and has the same specifications as the AC SPD
module to be replaced.

Do not replace an AC SPD module during a thunderstorm.

Procedure

Step 1

Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and ESD
gloves.

Step 2

Press the top and bottom of the faulty AC SPD module and pull it out, as shown in Figure
4-10.

Step 3

Install the new AC SPD module, as shown in Figure 4-10.

Figure 4-10

Replacing an AC SPD module

Step 4

Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist strap and ESD
gloves.

----End

Follow-up Procedure

Check that the alarm for the AC SPD is cleared.

Содержание TP48200A-DX08A1










































































Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды

Huawei TP48200A-DX08A1, Руководство пользователя

Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды