Huawei TP48200A-DX08A1 Скачать руководство пользователя страница 52

Страница: 52 / 73

TP48200A-DX08A1 and TP48200A-DX08A2 Telecom
Power
User Manual

4 Maintenance

Issue 06 (2019-11-15)

Figure 4-3

Removing the circuit breaker

Step 7

Switch off the new circuit breaker. Press the buckle at the circuit breaker base by using an
insulated flat-head screwdriver and install the new circuit breaker. Then loosen the buckle and
secure the circuit breaker to the guide rail.

Step 8

Tighten the screw that secures the lower port of the circuit breaker.

Step 9

Remove the insulation tapes from the output cables. Then connect the output cables to the
circuit breaker ports and tighten the screws.

Step 10

Switch the circuit breaker to ON, as shown in Figure 4-4.

Figure 4-4

Installing a circuit breaker

Step 11

Reinstall the cover and tighten the screws.

----End

4.4.3 Replacing the PCB of UIM02C

Prerequisites



You have obtained an ESD wrist strap, a pair of ESD gloves, an ESD box or bag, the
cabinet door key, and tools.

Содержание TP48200A-DX08A1










































































Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды

Huawei TP48200A-DX08A1, Руководство пользователя

Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды