Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 69

Страница: 69 / 99

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Figure 4-9

Removing the –48 V power cable

Step 5

Record the positions where the PCB of UIM02C connects to all the cables, and then
disconnect the cables.

Step 6

Remove the PCB, as shown in Figure 4-10.

Figure 4-10

Removing the PCB of UIM02C

Step 7

Take out the new PCB and install it.

Step 8

Connect all cables back to the new PCB based on the record made previously.

Step 9

Connect the –48 V power cable to the PCB of UIM02C.

Step 10

Push in the UIM02C and tighten the screws.

Step 11

Reconnect signal cables to the UIM02C panel based on the recorded information.

Step 12

Disconnect the ground cable from the ESD wrist strap, and remove the ESD wrist strap and
ESD gloves.

----End

Содержание Telecom Power TP48200A-HT19C3




































































































Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды

Huawei Telecom Power TP48200A-HT19C3, Руководство пользователя

Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды