Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 64

Страница: 64 / 99

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Figure 4-2

Installing a rectifier

Step 7

Remove the protective gloves.

----End

Follow-up Procedure

Pack the removed component and send it to the local Huawei warehouse.

4.4.2 Replacing an SMU

Prerequisites



The cabinet door key is available.



The new SMU is intact.

Procedure

Step 1

Push the locking latch towards the left.

Step 2

Pull the handle outwards and remove the SMU, as shown in Figure 4-3.

Figure 4-3

Removing an SMU

Step 3

Insert the new SMU into the subrack, push the locking latch towards the left, and pull out the
handle.

Step 4

Slide the SMU into the subrack slowly along the guide rails, push in the handle, and then push
the locking latch towards the right.

Step 5

Reset the parameters on the SMU.

Содержание Telecom Power TP48200A-HT19C3




































































































Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды

Huawei Telecom Power TP48200A-HT19C3, Руководство пользователя

Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды