Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 53

Страница: 53 / 99

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Maintenance
Item

Check Whether

Check Method

Repair When

Measures

normally.

and the
temperature.

cannot effectively
cool the air.

TEC04C.

Electrical
specifications

The output voltage
is normal.

Multimeter

The battery circuit
voltage or load
circuit voltage
exceeds its
threshold.

For details, see 4.2
Rectifying
Common Faults.

Preventive
maintenance
inspection (PMI)

Indicators are
normal.

By observing

An alarm is
generated.

Appearance

The paint or
electroplated
coating on the
cabinet flakes off or
has scratches.

By observing

The surface is
damaged or
distorted.

Repaint or repair
the shell.

Grounding

The ground point
properly connects
to the ground bar in
the equipment
room.

By observing the
grounding and
using a screwdriver
or wrench.

The cable
connecting the
ground point and
the ground bar in
the equipment room
is loose or
damaged.

Secure the ground
point or replace the
cable.

4.2 Rectifying Common Faults

4.2.1 AC Failure

Possible Causes



The AC input power cable is faulty.



The AC input circuit breaker is OFF.



The power grid is faulty.

Measures

Check whether the AC input cable is loose. If so, secure the AC input cable.

Check whether the AC input circuit breaker is OFF. If so, handle the fault which caused
the AC input circuit breaker to turn OFF and then switch on the circuit breaker.

Check whether the AC input voltage is lower than 50 V AC. If so, handle the power grid
fault.

Содержание Telecom Power TP48200A-HT19C3




































































































Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды

Huawei Telecom Power TP48200A-HT19C3, Руководство пользователя

Результаты поиска

Содержание Telecom Power TP48200A-HT19C3

Отзывы:

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренды по названию

Популярные бренды