Huawei Telecom Power TBC300A-DCA5 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 95

background image

TP48200A-HX09A1 and TBC300A-DCA5 Telecom
Power
User Manual

2 Overview

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

19

Item

TP48200A-HX09A1

TBC300A-DCA5

Rectifier

A maximum of four R4850G1s or
R4850N1s can be configured.

N/A

Site monitoring unit (SMU)

One SMU02B

N/A

User interface module (UIM)

One UIM02C

N/A

Sensor



Mandatory: one door status
sensor and one ambient
temperature sensor



Optional: one smoke sensor,
one ambient temperature and
humidity sensor, and one water
sensor

One door status sensor and one
battery temperature sensor

Lamp

Optional: one lamp

N/A

Battery

N/A

Battery compartment of two layers:
two front-access battery strings (12
V/100 Ah) can be configured.

Maximum output power

12 kW



Class B environments refer to indoor environments in which the ambient temperature and humidity
are not controlled and outdoor environments (with simple shielding measures) where humidity can
reach 100%.



Class C environments refer to sea environments or outdoor land environments (with simple
shielding measures) near pollution sources. If a site is near a pollution source, it is at most 3.7 km
away from salt water, such as the sea and salt lakes, 3 km away from heavy pollution sources, such
as smelteries, coal mines, and thermal power plants, 2 km away from medium pollution sources,
such as chemical, rubber, and galvanization industries, and 1 km away from light pollution sources,
such as packing houses, tanneries, and boiler rooms.

«
...
24
25
26
27
28
...
»

Содержание Telecom Power TBC300A-DCA5
































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TBC300A-DCA5

Бренд: GE Страницы: 146

Бренд: Paradyne Страницы: 16

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: ICP Страницы: 14

Бренд: Ubiquiti Страницы: 40

Бренд: ETAS Страницы: 69

Бренд: RAK Страницы: 30

Бренд: Renesas Страницы: 2

Бренд: Ravpower Страницы: 27

Бренд: Arbor Technology Страницы: 8

Бренд: Comway Страницы: 20

Бренд: Aurora Страницы: 6

Бренд: Juniper Страницы: 420

Бренд: ivideon Страницы: 11

PacketMate 1000

Бренд: General DataComm Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды