manualshive.com logo in svg

Huawei SUN2000-50KTL-JPM0, Руководство пользователя, Страница: 53 / 113

Поделиться
Скачать
Huawei SUN2000-50KTL-JPM0 Скачать руководство пользователя страница 53

SUN2000-(50KTL-JPM0, 50KTL-JPM1, 63KTL-JPM0) 
User Manual 

5 Electrical Connections 

 

Issue 01 (2018-09-30) 

Copyright © Huawei Technologies Co., Ltd. 

47 

 

Figure 5-18

 

Communication mode for a single SUN2000 

 

 

 

Figure 5-19

 shows the communication mode for multiple SUN2000s. 

If multiple SUN2000s are used, connect all the SUN2000s in daisy chain mode over an 
RS485 communications cable. 

Figure 5-19

 

Communication mode for multiple SUN2000s 

 

 

 

 

The RS485 communication distance between the SUN2000 at the end of the daisy chain and the 
SmartLogger cannot exceed 1000 meters. 

 

If multiple SUN2000s need to communicate with one another and are connected to a PC over the 
SmartLogger1000, a maximum of three daisy chains can be configured. 

 

If multiple SUN2000s need to communicate with one another and are connected to a PC over the 
SmartLogger2000, a maximum of six daisy chains can be configured. 

 

To ensure the system response speed, it is recommended that the number of devices on each daisy 
chain be less than 30. 

5.6.2 Installing the RS485 Communications Cable 

Selecting an Installation Mode 

An RS485 communications cable can be connected in two ways: 

 

Terminal block connection 

Recommended: Communications cable with a conductor cross-sectional area of 1 mm

2

 

and a cable outer diameter of 14–18 mm. 

 

RJ45 network port connection 

Содержание SUN2000-50KTL-JPM0


















































































































Отзывы:

Нет отзывов