Huawei SUN2000-196KTL-H0 Скачать руководство пользователя страница 31

Страница: 31 / 109

4.4 Installing the Mounting Bracket

Installation Precautions

Figure 4-8

shows the inverter mounting bracket dimensions.

Figure 4-8 Mounting bracket dimensions

NO TE

The inverter mounting bracket has four groups of tapped holes, each group containing four

tapped holes. Mark any hole in each group based on site requirements and mark four holes

in total. The two round holes are recommended.

Before installing the mounting bracket, remove the security torx wrench from the

mounting bracket and set it aside.

Figure 4-9 Removing a security torx wrench

4.4.1 Support-mounted Installation

Support-mounted Installation

Step 1 Install the mounting bracket.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

User Manual

4 Installation

Issue 02 (2020-10-30)

Содержание SUN2000-196KTL-H0














































































































Результаты поиска

Содержание SUN2000-196KTL-H0

Отзывы:

Бренды по названию

Популярные бренды

Huawei SUN2000-196KTL-H0, Руководство пользователя

Результаты поиска

Содержание SUN2000-196KTL-H0

Отзывы:

Бренды по названию

Популярные бренды