Specifi c Absorption Rate (SAR) of Mobile Terminals
This model Speed Wi-Fi NEXT W05 device complies with Japanese technical regulations and international guidelines regarding
exposure to radio waves.
This device was designed in observance of Japanese technical regulations regarding exposure to radio waves(*1) and limits to
exposure to radio waves recommended by a set of equivalent international guidelines. This set of international guidelines was
set out by the International Commission on Non-Ionizing Radiation Protection (ICNIRP), which is in collaboration with the World
Health Organization (WHO), and the permissible limits include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health condition.
The Japanese technical regulations and international guidelines defi ne the limits using a unit of measurement known as the
Specifi c Absorption Rate (SAR), which represents the average amount of radio frequency energy absorbed by the human body.
The SAR limit for mobile terminals is 2.0 W/kg. The highest SAR value for this device when tested for intended use described in
the instruction manual is 0.986 W/kg
(*2)
. There may be slight differences between the SAR levels for each product, but they all
satisfy the limit.
The actual SAR of this device while operating can be well below that indicated above. This is due to automatic changes in the
power level of the device to ensure it only outputs the minimum power required to communicate with a base station. Therefore
in general, the closer you are to a base station, the lower the power output of the device.
During communication, hold the device farther than 1.5 cm away from your body without including any metals. By doing
this, this data communication terminal complies with Japanese technical regulations and international guidelines regarding
exposure to radio waves.
The World Health Organization has stated that present scientifi c information does not indicate that use of mobile devices has
any harmful effects on the human body.
If you would like to know more detailed information, please refer to the WHO website.
http://www.who.int/docstore/peh-emf/publications/facts_press/fact_english.htm
Please refer to the websites listed below if you would like more detailed information regarding SAR.
○
Ministry of Internal Affairs and Communications Website:
http://www.tele.soumu.go.jp/e/sys/ele/index.htm
○
Association of Radio Industries and Businesses Website:
http://www.arib-emf.org/01denpa/denpa02-02.html
(Japanese)
○
HUAWEI TECHNOLOGIES CO., LTD. homepage:
http://consumer.huawei.com/jp/mobile-broadband/w05/
(Japanese)
○
au homepage:
https://www.au.com/english/
*1
Technical regulations are defi ned by the Ministerial Ordinance Related to Radio Law (Article 14-2 of Radio Equipment Regulations).
*2 Including other radio systems that can be simultaneously used.
Disposal and recycling information
This symbol (with or without a solid bar) on the device, batteries (if included), and/or the packaging, indicates that
the device and its electrical accessories (for example, a headset, adapter, or cable) and batteries should not be
disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and should
be taken to a certifi ed collection point for recycling or proper disposal.
For more detailed information about device or battery recycling, contact your local city offi ce, household waste
disposal service, or retail store.
Disposal of the device and batteries (if included) is subject to WEEE Directive Recast (Directive 2012/19/EU) and Battery
Directive (Directive 2006/66/EC). The purpose of separating WEEE and batteries from other waste is to minimize the potential
environmental impacts and human health risk of any hazardous substances that may be present.
Reduction of hazardous substances
This device and any electrical accessories are compliant with local applicable rules on the restriction of the use of certain
hazardous substances in electrical and electronic equipment, such as EU REACH, RoHS and Batteries (where included)
regulations, etc. For declarations of conformity about REACH and RoHS, please visit our web site http://consumer.huawei.com/
certifi cation.
EU regulatory conformance
■
RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 0.5 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■
Certifi cation information (SAR)
This device meets guidelines for exposure to radio waves.
Your device is a low-power radio transmitter and receiver. As recommended by international guidelines, the device is designed
not to exceed the limits for exposure to radio waves. These guidelines were developed by the International Commission on
Non-Ionizing Radiation Protection (ICNIRP), an independent scientifi c organization, and include safety measures designed to
ensure the safety of all users, regardless of age and health.
The Specifi c Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the body
when using a device. The SAR value is determined at the highest certifi ed power level in laboratory conditions, but the actual
SAR level during operation can be well below the value. This is because the device is designed to use the minimum power
required to reach the network.
The SAR limit adopted by Europe is 2.0 W/kg averaged over 10 grams of tissue, and the highest SAR value for this device
complies with this limit.
■
Statement
Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. The most recent and valid version of the DoC (Declaration of Conformity) can be
viewed at http://consumer.huawei.com/certifi cation. This device may be operated in all member states of the EU. Observe
national and local regulations where the device is used. This device may be restricted for use, depending on the local network.
Restrictions in the 2.4 GHz band:
Norway:
This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund.
Restrictions in the 5 GHz band:
WLAN function of this device is restricted only to indoor use when operating in the 5150 to 5350 MHz frequency range.
FCC Regulatory Compliance
■
RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 1 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■
Certifi cation information (SAR)
This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications
Commission (USA).
The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue.The highest SAR value reported to the FCC for
this device type complies with this limit.
■
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: Any changes or modifi cations to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance
could void the user’s authority to operate the equipment.
Restrictions in the 5 GHz band:
Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations to reduce any potential for harmful
interference to co-channel Mobile Satellite System (MSS) operations.
■
FCC ID
Check FCC ID in the following steps.
“Settings”
→
“About”
→
“Certifi cation”
Export Administration Regulations
The product and its accessories may be subject to the Japan Export Administration Regulations (“Foreign Exchange and
Foreign Trade Law” and its related laws). In addition, U.S. Re-export Regulations (Export Administration Regulations) may apply
to the product and its accessories. To export and re-export the product and its accessories, take the required measures on
your responsibility and at your expenses. For details on the procedures, contact the Ministry of Economy, Trade and Industry or
the U.S. Department of Commerce.
Trademarks
• Wi-Fi
®
, Wi-Fi Alliance
®
, Wi-Fi CERTIFIED
®
, WPA™, WPA2™, Wi-Fi Protected Setup™ logos are registered trademarks or
trademarks of Wi-Fi Alliance.
• The Bluetooth word mark and logo are registered trademarks owned by the Bluetooth SIG, INC., and HUAWEI
TECHNOLOGIES is licensed to use these trademarks.
• HUAWEI is a registered trademark or trademark of HUAWEI TECHNOLOGIES CO., LTD. in China.
• Other company names and product names referred to in this manual are trademarks and registered trademarks of respective
companies. The ® marks or TM marks may be omitted in this manual.
Policy on the protection of personal information
Please refer to the websites listed below if you would like more detailed information regarding the HUAWEI TECHNOLOGIES
CO., LTD. policy on the protection of personal information.
http://consumer.huawei.com/en/privacy-policy/index.htm
• Since Bluetooth
®
and wireless LAN (Wi-Fi
®
) functions use the same frequency band, using the both functions at the same
might cause radio wave interference resulting in decreased communication speed or disconnection from the network. If
connection fails, stop using either of the Bluetooth
®
and wireless LAN (Wi-Fi
®
) functions.
Bluetooth
®
function and wireless LAN (Wi-Fi
®
) function of the product use 2.4GHz band.
2.4FH4/DS4/OF4/XX8
• Bluetooth
®
function
The product uses the 2.4 GHz band. FH4 is used as the FH-SS modulation scheme. The interference distance is about 40
m or less. XX8 is used as the other modulation scheme. The interference distance is about 80 m or less. This means that all
bandwidths are used, and that bands of mobile unit identifi cation devices can be avoided.
•
Wireless LAN (Wi-Fi
®
) function
The product uses the 2.4 GHz band. DS-SS and OFDM are used as the modulation schemes. The interference distance is about
40 m or less. This means that all bandwidths are used, and that bands of mobile unit identifi cation devices can be avoided.
Available channels differ depending on the country.
For use in an airplane, check with the airline company in advance.
Cautions on using 5GHz band
Wireless LAN (Wi-Fi
®
) function of the product uses 5GHz band. Using the 5.2 GHz band and 5.3 GHz band outdoors is
prohibited by the Radio Law.
The channels used on the product are as follows.
W52 (5.2 GHz band/36, 40, 44, 48 ch)
W53 (5.3 GHz band/52, 56, 60, 64 ch)
W56 (5.6 GHz band/100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch)
PIN code
■
PIN code
●
To prevent unauthorized use of the au IC card by a third party, you can set the product to require PIN code entry every time
the power is turned on. You need to enter the PIN code when setting whether to enter the PIN code or not.
●
If the PIN code is incorrectly entered three times consecutively, the PIN code will be locked. You can unlock the PIN code
using PUK code.
* By default setting, PIN code is “1234” and PIN code entry is not needed. However, you can change the PIN code to any
four- to eight-digit number and PIN code entry setting (entry is needed) as necessary. When an entry of security code is
required for making settings, change the initial value of the security code to your own number and then use it.
* PIN code is not reset by resetting the product.
■
PUK code
●
In case the PIN code is locked, you can unlock it by entering the PUK code.
* PUK code is an eight-digit number given at the time of purchase, and is printed on the back side of the plastic card on
which your au IC card is attached.
* After entering the PUK code, you need to set a new PIN code in “PIN Code Management”.
* If the PUK code is incorrectly entered ten times consecutively, contact an au shop, PiPit or Customer Service Center.
Notes on data communication charge
•
Since a constant Internet connection is possible with the product, data communication may be performed automatically.
• To confi gure various settings, connection to the Internet is required, to which data communication charge applies.
After-sales service
■
When asking for repair
For repair, contact Repair and Delivery Support Center
During the warranty period
Repairs will be done based on the terms of services of the free-of-charge repair warranty
described on the warranty card.
Outside the warranty period
We shall repair the product for a charge as requested by the customer if repair renders it usable.
* Warranty period is one year from the date you newly purchased the product.
•
Before handing in the product for repair, make a backup of the contents of memory since they may disappear during repair.
Note that the Company shall not be liable for any damages and loss of income should the contents of memory be altered or lost.
•
Recycled parts that meet the Company’s quality standards are sometimes used for repair.
•
Collected au products by Replacement mobile phone delivery service which you used before are recycled to products for
replacement after repairs. Also replaced parts by au after-sales service are collected and recycled by KDDI. They are not
returned to customers.
•
Modifi ed, remodeled, analyzed (including software alteration, analysis (including rooting), reverse engineering, decompiling,
or disassembling) products, or products repaired by repair offi ces other than the Company etc. specifi ed are out of warranty
and repairs might be refused.
■
Performance parts for repair
The Company retains performance parts for repair of Speed Wi-Fi NEXT W05 main unit and its peripherals for four years after
discontinuation of production.
“Performance parts for repair” refers to parts required for maintaining the functions of the product.
■
Warranty card
At the store of purchase, thoroughly check and read the name of the retailer, date of purchase and other necessary details fi lled
in on the warranty card, and be sure to keep it in a safe place.
■
Repair and Delivery Support
An after-sales service membership program on a monthly basis called “Repair and Delivery Support” (monthly fee: 380 yen
excluding tax) is available for using your au product for a long time without worries. This service expands coverage for many troubles
including malfunction, theft and loss. For details of this service, refer to au homepage or contact Repair and Delivery Support Center.
•
You can apply for membership only at the time of purchasing your au product.
•
Once you cancel the membership, you cannot reapply for it until you purchase an au product next time.
•
Note that when changing the model or purchasing an extra au product, this service only covers the most recently purchased
au product.
•
When an au product is handed over to you or someone else, the Repair and Delivery Support membership is also handed
over to the successor of the product.
•
When you get a new au product by changing the model or purchasing an extra product, the “Repair and Delivery Support”
membership for the old au product is automatically canceled.
•
Service contents are subject to change without notice.
■
au Nano IC Card 04 LE
The au Nano IC Card 04 LE is lent to you by au. In case of loss or damage, the card will be replaced at your expense. When
malfunction is suspected, or in case of theft or loss, contact an au shop or PiPit.
■
au after-sales service information
Service
Repair and Delivery Support
Member
Others
Replacement
mobile phone
delivery service
Spontaneous
failure
1st year
Free of charge
No recompense
2nd year or later
See table of “Replacement mobile phone
delivery service” (Member) Customer
charge
Partially damage, water soak,
irreparable damage, theft or loss
Holding over and
repair
Spontaneous
failure
1st year
Free of charge
Free of charge
2nd year or later
Free of charge (for 3 years)
Actual cost
Partially damage
Customer charge
Upper limit: 5,000 yen
Water soak, irreparable damage
Customer charge
10,000 yen
Loss, theft
No recompense
No recompense
(model change)
* Charge amounts are all tax-excluded.
“Replacement mobile phone delivery service” (Member) Customer charge
Condition
1st
2nd
Basic charge
5,000 yen/
Longtime user benefi t
*1
3,000 yen
8,000 yen/
Longtime user benefi t
*1
6,000 yen
“WEB
割引
(Discount for web application)”
*2
and “
代用機
なし割引
(Discount for nonuse of substitute)”
*3
applied
4,000 yen/
Longtime user benefi t
*1
2,000 yen
7,000 yen/
Longtime user benefi t
*1
5,000 yen
Only “
代用機なし割引
(Discount for nonuse of
substitute)”
*3
applied
4,500 yen/
Longtime user benefi t
*1
2,500 yen
7,500 yen/
Longtime user benefi t
*1
5,500 yen
* Charge amounts are all tax-excluded.
*1
This discount applies to customers who have used au for three years (25 months) or more, and all the lines within
that customer’s Family Discount. For customers using a data communication device or tablet, this discount applies to
customers who are subscribed to a set discount (WIN Single Set Discount or Smartphone Set Discount) and have been
under the contract of the line eligible for the set discount for 3 years or more.
*2
WEB
割引
(Discount for web application): 500 yen reduction from the customer charge is applied for application of
“Replacement mobile phone delivery service” via au homepage.
A substitute device is not rent for “WEB
割引
(Discount for web application)”, instead, “
代用機なし割引
(Discount for
nonuse of substitute)” is also applied together.
*3
代用機なし割引
(Discount for nonuse of substitute): 500 yen reduction from the customer charge is applied if you do not
use a substitute device when using “Replacement mobile phone delivery service”.
For details, refer to au homepage.
Online Reception Desk (24 hours a day over the Internet)
* Available only from PC or smartphone
https://www.au.com/support/service/mobile/trouble/repair/application/
Replacement mobile phone delivery service
•
When you have trouble with your au product, a replacement device (same model, same color
*
) is delivered by calling to.
Return your damaged au product within 14 days after a replacement device is delivered.
* If the same model in the same color is diffi cult to provide, a replacement device of a model in a color that are specifi ed by
KDDI is provided.
•
Available up to twice in a year from the day you use this service as a start day. If you do not use this service in the past year
for the subscription to this service, it will be 1st and if you use, it will be the 2nd.
* For details, refer to au homepage.
•
In the event of theft or loss, an au IC card has to be reissued when using this service. In such a case, the au IC card reissue
fee of 1,900 yen is separately required.
Holding over and repair
•
Damage or malfunction due to a deliberate act or alterations (including disassembly and alteration, part replacement, or
painting) are not covered by the warranty.
•
You cannot receive a reduction for a replacement of the outer casing due to stains, scratches, paint removal, etc.
December 2017, 1st Edition
Sold by: KDDI CORPORATION, OKINAWA CELLULAR TELEPHONE COMPANY
Imported by: HUAWEI Technologies Japan K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD.
●
Do not place the product on unstable location such as wobbly platform or inclined place. The product might drop resulting
in cause of malfunction.
●
Do not exceed the rating of a power outlet or wiring device when charging the product, for example, by starburst connection etc.
■
Main unit
●
Since the battery is built into the product, you cannot replace it yourself. For replacing the battery, contact an au shop or
Customer Service Center.
●
Do not forcefully press, tap or intentionally subject the display panel to strong impact. Doing so might cause scratching or
damage.
●
Do not forcefully press your fi ngernails, sharp objects or hard objects against keys or display panel surface. Doing so
might cause scratching or damage.
●
The touch panel is designed to be lightly touched by fi ngers. Do not apply strong pressure with your fi ngers or sharp
pointed objects (such as fi ngernails, ballpoint pens and pins) on the touch panel.
In the following cases, the touch panel might not respond or errors in operation might occur.
• Operating with gloved hand
• Operating with tip of fi ngernail
• Operating when a foreign object is put on the panel
• Operating with a protective sheet or sticker attached on the panel
• Water droplet or dew condensation is on the display
• Operating when your fi nger is wet or moist by sweat.
●
Never use modifi ed the product. Use of a modifi ed device violates the Radio Law and Telecommunications Business Act.
The product obtains a technical standards conformity certifi cation of specifi ed wireless equipment based on the Radio Law
and a technical standards conformity approval based on the Telecommunications Business Act, and as a proof, you can
check the “Technical Conformity Mark
” with the product.
To display the mark, in the Home screen, tap “Settings”
→
“About”
→
“Certifi cation”. If any modifi cation is made to the
internal components, the certifi cation of conformity with technical regulations will become invalid. Never use the product
without the valid certifi cation. Doing so violates the Radio Law and Telecommunications Business Act.
●
Take care not to place magnetized items such as magnetic cards, speakers and TV sets near the product, as it might
cause a malfunction.
Putting a strong magnetism close to the product might cause false operation.
●
Do not bring magnetized cards such as cash cards, credit cards and pre-paid cards closer to the product. Doing so might
cause loss of the recorded data.
●
When you put the product in your pocket or bag, take care so that the display panel does not come in contact with metal
objects or other hard objects. Doing so might cause scratching or damage. Also, be careful not to scratch or damage the
display panel by using a strap whose metal or other hard part comes in contact with the display panel.
●
When suddenly brought into a warm place from a cold place, or when in a humid location, or when used where temperature
suddenly changes (e.g. near the air discharge port of an air conditioner), water droplets (i.e. condensation) sometimes are
formed inside the product. Note that when used under such conditions, the humidity might cause corrosion or a malfunction.
●
Use the product with the Nano IC Card slot cover closed. If you use with the au Nano IC Card slot cover open, dust or
water might get inside causing a malfunction.
●
Do not allow liquids, metal objects, or other foreign objects to get inside of the Nano IC Card slot. Doing so might cause a
malfunction.
●
Do not give strong impact on the product such as dropping, throwing, stomping. Doing so might cause a malfunction.
●
Do not place the product directly on a sandy beach, etc. If sand etc. gets inside of the product, it might cause a malfunction.
■
Touch Panel
●
Do not put stickers or sheets (e.g. commercially available protective fi lms, peep prevention sheets) on the display panel.
Doing so might hinder correct operation of the touch panel.
●
When carrying the product in your pocket or bag, take care not to put the touch panel close to metals or other conductive
materials, as it might cause false operation of the touch panel.
■
Internal Battery
(The internal battery of the product is a lithium-ion battery)
The internal battery is not fully charged at the time of purchase. Charge the battery before using the
product. Charge the battery before using if you have not used the product for a long time.
●
Use in very hot or cold environments, for example, when left in an automobile with the windows closed in summer, will
cause the internal battery capacity to drop and shorten the available battery usage time. That also shorten the internal
battery life. Try to use the internal battery as far as possible at room temperature.
●
The internal battery gradually discharges after charging even if the product is not used. The internal battery might
discharge completely after long time no use. Charge before using.
●
The internal battery is a consumable part. If the performance of a battery does not recover (e.g. the usable time after each
charge has become extremely short), the battery is at the end of service life, so stop use. The battery is built into the product.
For repair, the product must be collected to au shop etc. and charges will be incurred. And you may not use the product during
certain period of time. Please be forewarned. Note that the length of service life varies depending on the usage condition, etc.
●
Internal battery sometimes swells up as they approach the end of their service life. This is due to the properties of lithium-
ion batteries, and is not a problem in terms of safety.
■
Charging equipment
●
Do not wrap the cord of the specifi ed charging equipment (sold separately) around the adapter itself. Do not bend
connection part of charging equipment and power plug forcibly. Do not place heavy objects on a cord of adapter or power
cable, or do not apply unreasonable force to the cord such as pulling. Doing so might cause a malfunction.
●
Hold the power plug of the specifi ed charging equipment when removing from an outlet. If you pull the cable, the cable
might be damaged.
■
USB2.0TypeC-A cable (sample)
●
Do not bend the connection part of the plug of the cable and the product, a PC, etc. forcibly. Do not place heavy objects
on the cord of cable, or do not apply excessive force to the cord such as pulling. Doing so might cause a malfunction.
●
For disconnecting the product, a PC, etc., grasp the plug. Pulling the cord might damage the cable.
■
au IC card
●
Do not forcibly remove or insert the au IC card. Be careful not to exert excessive force when inserting the card into the product.
●
You are responsible for any damage caused by inserting your au IC card into some other IC card reader/writer, etc.
●
Do not put a sticker etc. on au IC card.
●
Do not insert the au IC card with a conversion adapter. Doing so might cause a malfunction.
●
Do not damage the card by using the product in a hot place, dropping into fi re, contacting to the metal parts with foreign
object, giving an impact, bending, applying load, etc. Doing so might cause loss of data or a malfunction.
■
Copyrights & portrait rights
●
You are not allowed to copy, distribute, publish, modify or edit the data you downloaded using the product without consent
of the copyright holder, except for personal use, under the copyright law.
In addition, do not use or modify portraits or names of other individuals without the consent, as it might infringe on rights of
portrait.
■
Backup content on the product
●
Please back up important content you registered to the product. Content recorded to the memory of the product might
disappear or be altered by unexpected factors, such as static electricity or a malfunction, repair, mishandling, etc.
Notes on using Bluetooth
®
/Wireless LAN (Wi-Fi
®
) functions
•
The Bluetooth
®
function and wireless LAN (Wi-Fi
®
) function of the product conforms to domestic wireless standards in Japan,
FCC standards, and EC directives and obtained the certifi cation.
•
Use 5 GHz band wireless LAN (Wi-Fi
®
) function of the product in Japan. The 5 GHz band wireless LAN (Wi-Fi
®
) function of
the product conforms to domestic wireless standards in Japan, and has been certifi ed. Use of it overseas may be subject to
punishment by law.
•
Use of Bluetooth
®
function and Wireless LAN (Wi-Fi
®
) function may be restricted in some countries/regions. Before using the
product overseas, check the relevant laws and regulations of the country/region you visit.
•
The 2.4 GHz band used by wireless LAN (Wi-Fi
®
) or Bluetooth
®
devices is operated by various other devices. For this reason, the
communication speed and connectable range may be decreased, or disconnection may occur, due to interference by other devices.
•
Do not use the product in places near electric products, AV and OA equipment or other magnetized devices, or where
electromagnetic waves are generated.
•
Subjecting the product to magnetic or electrical noise might increase noise and hinder the communications. (The product is
particularly susceptible to noise when it used near a microwave oven.)
•
Using the product near a TV, radio or similar appliance might cause reception interference and disrupt TV images.
•
Searching might not be successful if there are multiple wireless LAN (Wi-Fi
®
) access points near to the product or the same
channel is being used.
•
Use of electric devices on board is restricted. Follow the instructions of each airline company.
•
The communication speed and connectable range vary depending on the distance between communication devices,
obstacles and the devices used.
Cautions on using 2.4 GHz band
Bluetooth
®
function/Wireless LAN (Wi-Fi
®
) function of the product uses 2.4 GHz band. In this frequency band, other similar
wireless stations, in-plant wireless stations for mobile unit identifi cation that require a license to use, such as factory production
lines, specifi c small power wireless stations that do not require licenses, amateur wireless stations (collectively called “other
wireless stations” from here on) are operated in addition to home electrical appliances such as microwave ovens, devices for
industrial, scientifi c and medical devices.
* The product cannot perform data communication using Bluetooth
®
function.
1. Before using the product, make sure that “other wireless stations” are not in operation nearby.
2. In the event that instances of radio wave interference have occurred between the product and “other wireless stations”,
immediately either relocate the product or stop operation of the device (stop emission of radio waves).
3. If you are unclear on any points or are troubled by anything, contact an au shop or Customer Service Center.
•
Connections between the product and all Bluetooth
®
/wireless LAN (Wi-Fi
®
) devices have not been confi rmed. Therefore,
connections with all Bluetooth
®
/wireless LAN (Wi-Fi
®
) devices are not guaranteed.
•
The product supports security features for wireless communications that are compliant with the wireless LAN (Wi-Fi
®
)
standard specifi cations, but the security may not be suffi cient depending on the usage environment and confi guration. Be
careful when making data communication using wireless LAN (Wi-Fi
®
) function.
•
Wireless LAN (Wi-Fi
®
) has the advantage that it can be freely connected anywhere within the radio wave range, as it uses
radio waves for exchanging information. At the same time, there is a risk that a malicious third party may obtain unauthorized
access if security settings have not been confi gured. You are recommended to confi gure security settings before using it at
your decision and responsibility.
•
The Company assumes no responsibility for leakage of data or information that may occur during wireless LAN (Wi-Fi
®
)
communication.
