Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 532 / 553

background image

reset coldstart
quit
esl user
mgpstnuser batadd 0/2/0 0/2/23 0 terminalid 0 telno 83110001
mgpstnuser modify 0/2/0 priority cat2
quit
pstnport
pstnport attribute batset 0/2/0 0/2/23 reverse-pole-pulse enable
quit
save

10.4.4 Configuring the FTTB and FTTC VoIP Services (Based on the
SIP Protocol)

The OLT is connected to a remote ONU that supports SIP by using the GPON port to provide
users with the VoIP service.

Service Requirements

l

Users directly uses the existing phone sets for the voice service and no additional investment
is required.

l

The voice data is carried over the IP network, which reduces the communication costs to
a great extent without compromising the communication quality.

l

Compared with traditional PSTN networks, IP-based networks provide more powerful
service functions and richer user experience.

l

The polarity-reversal accounting is supported.

Prerequisite

l

The PSTN user data corresponding to the SIP interface must be configured on the IMS.

l

Run the

display board 0

command to ensure that the

Status

of the voice board of ONU is

Normal

.

Background Information

ONUs that support SIP include the MA5616, MA5603T.

An ONU support either H.248 or SIP. To query the current voice protocol on an ONU, run the

display protocol support

command. To change the voice protocol to the other one, delete the

MG interface and run the

protocol support

command. After the configuration is complete, save

it and restart the system to make the configuration take effect.

WARNING

This operation interrupts the ongoing services carried on the currently used MG interface. Hence,
exercise caution when performing this operation.

An ONU support either H.248 or SIP. To query the current voice protocol on an ONU, run the

display protocol support

command. To change the voice protocol to the other one, delete the

MG interface and run the

protocol support

command. After the configuration is complete, save

it and restart the system to make the configuration take effect. This operation interrupts the
ongoing services carried on the currently used MG interface. Hence, exercise caution when
performing this operation.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

521

«
...
530
531
532
533
534
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

Бренд: ICP DAS USA Страницы: 8

Бренд: Salto Страницы: 2

Бренд: A10 Страницы: 52

Бренд: H3C Страницы: 21

Бренд: Planet Страницы: 20

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Juniper Страницы: 190

Бренд: process-informatik Страницы: 8

Supero SAS-826A

Бренд: Supero Страницы: 16

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: Kontron Страницы: 42

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды