Huawei SmartAX MA5616 Скачать руководство пользователя

Страница: 397 / 553

Item

Data

Upstream
priority

The 802.1p priorities are used. The VoIP service has priority 6, IPTV service
priority 5, and Internet service priority 1.

Configuration Flowchart

Figure 8-15

shows the flowchart for configuring the triple play service in the single-PVC for

multiple services mode based on the user-side 802.1p priority.

Figure 8-15

Flowchart for configuring the triple play service in the single-PVC for multiple

services mode based on the user-side 802.1p priority

Procedure

Configure the Internet service.
1.

Create a VLAN and add an uplink port to the VLAN.

huawei(config)#

vlan 102 smart

huawei(config)#

port vlan 102 0/0 1

Configure a traffic profile.

–

Because the VoIP, IPTV, and Internet services are provided through the same port,
you must set the 802.1p priority of each service.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

386

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды

Huawei SmartAX MA5616, Руководство по настройке

Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды