Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 303 / 553

background image

Default Configuration

lists the default settings of the attributes of the ISDN BRA user. When configuring

these attributes, you can modify the values according to the service requirements.

Table 7-24

Default settings of the attributes of the ISDN BRA user

Parameter

Default Settings

Priority of the ISDN BRA user

cat3: (common user)

Flag of reporting the UNI fault of the ISDN
BRA user

Disable

Threshold for the number of auto recoveries
from deterioration faults

20

Procedure

Step 1

In global config mode, run the

esl user

command to enter the ESL user mode.

Step 2

Run the

mgbrauser add

command to add an ISDN BRA.

l

When

iid-map

in the

iua-linkset add

command is configured to 1, interfaceid must be

configured and be different from the interfaceid of other users in the same link set.

l

The terminal ID of an ISDN BRA user must be different from the terminal IDs of other users.

l

If the MG interface does not support the terminal layering function, the terminal ID must be
configured when an ISDN BRA user is added. In addition, the terminal ID must differ from
the terminal ID of the existing ISDN BRA user by an integer multiple of 2. For example, to
add the first ISDN BRA user, the terminal ID is 2; to add the second ISDN BRA user, the
terminal ID is 4; to add the third ISDN BRA user, the terminal ID is 6; the rest may be deduced
by analogy.

l

If the MG interface supports the terminal layering function, the terminal ID cannot be
configured when an ISDN BRA user is added on the MG interface. The system automatically
allocates a terminal ID for the user.

Step 3

Run the

display mgbrauser attribute

command to check whether the ISDN PSTN user data is

the same as the data plan.

Step 4

(Perform this step only when you need to modify the attributes of the ISDN BRA user.) Run the

mgbrauser attribute set

command to configure the attributes of the ISDN BRA user.

Step 5

(Perform this step only after you modify the attributes of the ISDN BRA user.) Run the

display

mgbrauser attribute

command to query whether the configured attributes of the ISDN BRA

user are the same as the data plan.

----End

Example

Assume the following configurations:

l

Link set ID: 0

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

292

«
...
301
302
303
304
305
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

Бренд: DataRemote Страницы: 2

Бренд: Xinje Страницы: 76

EK-FC1080 GTX Ti TF6

Бренд: ekwb Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: Telex Communications Страницы: 28

Бренд: Radicom Страницы: 27

CNPS7000A Series

Бренд: ZALMAN Страницы: 9

Бренд: BEC Страницы: 159

Бренд: B&B Electronics Страницы: 2

Wireless Connectivity Cape

Бренд: Element14 Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды