Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 30 / 553

background image

Figure 3-9

Example network for configuring outband management over a LAN in the telnet

mode

MA5616

PC

PC

PC

LAN

In this example network, the IP address of the maintenance Ethernet port of the MA5616 and
the IP address of the maintenance terminal are in the same network segment. You can also
manage the MA5616 through an outband channel by directly connecting the maintenance
Ethernet port of the maintenance terminal to the maintenance Ethernet port on the control board
of the MA5616.

Data Plan - LAN

provides the data plan for configuring outband management over a LAN in the telnet

mode.

Table 3-1

Data plan for configuring outband management over a LAN in the telnet mode

Item

Data

Maintenance Ethernet port of the
MA5616

IP address: 10.10.20.2/24

Ethernet port of the maintenance
terminal

IP address: 10.10.20.3/24

Networking - WAN

Figure 3-10

shows an example network for configuring outband management over a WAN in

the telnet mode.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

19

«
...
28
29
30
31
32
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Panasonic Страницы: 44

Бренд: VMIC Страницы: 126

Бренд: Conceptronic Страницы: 2

Бренд: Patton electronics Страницы: 12

LinkSmart KW6515

Бренд: Kasda Страницы: 31

FireWire 800 + Hi-Speed USB Combo

Бренд: SIIG Страницы: 20

Бренд: Renesas Страницы: 20

Бренд: MC Страницы: 21

Бренд: Eaton Страницы: 14

Бренд: Aethra Страницы: 2

Бренд: Lanner Страницы: 59

Бренд: Paradyne Страницы: 6

Бренд: SeaLevel Страницы: 34

Бренд: IFM Electronic Страницы: 14

Бренд: MFJ Страницы: 11

Бренд: Microchip Technology Страницы: 9

Aquaduct 240 eco

Бренд: Aqua Computer Страницы: 20

Бренд: Aurora Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды