Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 295 / 553

background image

Example

To configure software parameter 11 of H.248-based MG interface 0 to 1 so that the MG interface
supports emergency standalone and allows only internal calls, do as follows:

huawei(config)#

interface h248 0

huawei(config-if-h248-0)#

mg-software parameter 11 1

huawei(config-if-h248-0)#

display mg-software parameter 11

-------------------------------------------------
Interface Id:0 para index:11 value:1
-------------------------------------------------
APPENDIX:
-------------------------------------------------
Interface software parameter name:
11: Stand alone support
0: None
1: Inner
2: Emergency
3: Both

7.3.1.6 (Optional) Configuring the Ringing Mode of an MG Interface

This topic describes how to configure the ringing mode of an MG interface to meet different
user requirements.

Context

Add the ringing mode mapping records of a specified MG interface. After the adding is
successful, the MG interface can obtains the ringing mode according to the peer parameters
issued by the MGC and then play the ringing to the user in this mode.

Procedure

Step 1

Check whether the ringing mode meets the requirements.

Check whether the preset ringing mode in the system meets the requirements according to the
Usage Guidelines of the

mg-ringmode add

command.

l

If the preset ringing mode meets the requirements, go to

l

If the preset ringing mode does not meet the requirements, proceed to

Step 2

Configure the user-defined ringing mode.

In the global config mode, run the

user defined-ring modify

command to configure the break-

make ratio of user-defined ringing mode to form a ringing mode that meets the user requirement.

CAUTION

The system supports 16 user-defined ringing modes, which can be modified but cannot be added
or deleted.

Step 3

Enter the MG interface mode.

Run the

interface h248

command to enter the MG interface mode.

Step 4

Add a ringing mapping.

Run the

mg-ringmode add

command to add a ringing mapping.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

284

«
...
293
294
295
296
297
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: GE Страницы: 4

Бренд: EAW Страницы: 2

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: Yamaha Страницы: 4

Бренд: Ubiquiti Страницы: 23

Ethernet Communication Module DVPEN01-SL

Бренд: Delta Electronics Страницы: 54

Бренд: ZALMAN Страницы: 4

RealPort Ethernet 10/100

Бренд: Xircom Страницы: 30

Бренд: Tektronix Страницы: 178

Бренд: Aewin Technologies Страницы: 86

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Бренд: Zhone Страницы: 2

Бренд: National Instruments Страницы: 26

Бренд: Icy Box Страницы: 2

Бренд: LevelOne Страницы: 11

Бренд: netsys Страницы: 164

Бренд: Spirent Страницы: 22

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды