manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке, Страница: 23 / 553

Поделиться
Скачать
Huawei SmartAX MA5616 Скачать руководство пользователя страница 23

3.1 Configuring the Maintenance Terminal

This topic describes three modes of managing the MA5616 from the maintenance terminal.

3.1.1 Configuring Management Through a Local Serial Port

This topic describes how to connect the maintenance terminal to the MA5616 through a local
serial port, log in to the MA5616, and then manage the MA5616 from the maintenance terminal.

Networking

Figure 3-1

 shows an example network for configuring management through a local serial port.

Figure 3-1

 Example network for configuring management through a local serial port

MA5616

RS-232 serial 

port cable

PC

 

Configuration Flowchart

Figure 3-2

 shows the flowchart for configuring management through a local serial port.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

12

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов