Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 19 / 553

background image

2.1 Checking the Software Version

This topic describes how to check whether the current software version meets the deployment
requirement.

Prerequisites

You must be logged in to the MA5616. For details about how to log in to the device, see

Configuring the Maintenance Terminal

.

Procedure

l

The procedure of checking the software version through the MA5616 is as follows:
1.

In the user mode, run the

display language

command to check whether the multi-

language information supported by the system and the system version meet the
deployment requirement.

2.

In the user mode, run the

display version

command to check whether the versions of

the host software and patch that is running in the system meet the deployment
requirement.

l

The procedure of checking the software version through the iManager U2000 is as follows:

1.

In the

Workbench

window, double-click

. The

Main Topology

window is

displayed. Click

.

2.

In the

Search

dialog box, select

NE

from the

Search Type

drop-down list and enter

the description of the MA5616 to be queried. Then, click

Search

.

3.

In the search result, select the desired MA5616. Click

Locate

and select

Locate to

NE Panel

from the list. In the

Device Detailed Info

tab page, verify that the device

type and activated patch meet the deployment requirement.

----End

Result

l

The versions of the host software and patch meet the deployment requirement.

l

If the versions do not meet the deployment requirement, contact Huawei technical support
center to upgrade the host software if necessary. For details about the upgrade, see the

MA5616

Upgrade guide

.

2.2 Checking the Board Status

This topic describes how to check whether the inserted board is the same as the board specified
in the data plan, and whether the boards are in the normal state.

Procedure

l

The procedure of checking the board status through the MA5616 is as follows:
1.

Run the

display board

command to check whether the board information (including

the board types and the slots housing the boards) meets the data plan and whether the
boards are in the normal state.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

2 Checking Before the Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

8

«
...
17
18
19
20
21
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: REXROTH Страницы: 68

Бренд: LORD Страницы: 9

Бренд: Acqiris Страницы: 22

Бренд: FOR-A Страницы: 2

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: Kanguru Страницы: 13

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренд: UfiSpace Страницы: 34

Бренд: Accton Technology Страницы: 78

Бренд: Connectland Страницы: 10

Бренд: Zoom Страницы: 31

J-Link-OB-STM32F072-128KB

Бренд: Segger Страницы: 18

CHEETAH ST34501FC

Бренд: Seagate Страницы: 68

Бренд: Softing Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды