Huawei S5700 Series Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 415

background image

#
sysname Member-2
#
vlan batch 10
#
cluster enable
ntdp enable
ntdp hop 3
ntdp timer 10
ndp enable
#
interface Vlanif10
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 10
ntdp enable
ndp enable
#
cluster
mngvlanid 10
administrator-address 0001-0001-0001 name HUAWEI
#
return

l

Configuration file of Member-3.

#
sysname Member-3
#
vlan batch 10
#
cluster enable
ntdp enable
ntdp hop 3
ntdp timer 10
ndp enable
#
interface Vlanif10
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 10
ntdp enable
ndp enable
#
cluster
mngvlanid 10
administrator-address 0001-0001-0001 name HUAWEI
#
return

3.6.2 Example for Configuring the Interconnection of FTP Servers
and Devices in and out of the HGMP Cluster (in NAT Mode)

Networking Requirements

As shown in

, all the Layer 2 switches belong to the same cluster. Administrator-1 is

the administrator switch of the cluster and other switches are member switches. The member ID
of Member-1 is 1, the member ID of Member-2 is 2 and the member ID of Member-3 is 3.

To upload files to Member-1, Member-2, and Member-3 or download files from them, you can
set up an FTP connection between the devices out of the cluster and member switches in NAT
or non-NAT mode.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

3 HGMP Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

118

«
...
127
128
129
130
131
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S5700 Series

Бренд: D-Linke Страницы: 32

Бренд: IBM Страницы: 32

Бренд: Ubiquiti Страницы: 50

Бренд: bintec elmeg Страницы: 33

Бренд: Zonet Страницы: 53

Бренд: axing Страницы: 4

Бренд: ZyXEL Communications Страницы: 79

Бренд: Thecus Страницы: 120

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

AceroDURO 100/S100

Бренд: CNC-Step Страницы: 86

NetCon FBR-1409TX

Бренд: LevelOne Страницы: 88

Бренд: NetComm Страницы: 65

Бренд: Aerotech Страницы: 62

Бренд: Camozzi Страницы: 22

Бренд: Axtrinet Страницы: 49

Бренд: National Instruments Страницы: 4

Бренд: NASdeluxe Страницы: 6

Бренд: Huawei Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды