Huawei RRU5303 Скачать руководство пользователя страница 16

Страница: 16 / 135

RRU5303
Installation Guide

3 Information About the Installation

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Item

Silkscreen

Remarks

B T/R

TX/RX port B (4.3-10 straight connector),
supporting RET signal transmission

RET

Communication port for the RET antenna,
supporting RET signal transmission

(2) Ports in the
cabling cavity

RTN(+)

Power supply socket, For details about RRU
power cable appearance and specifications,
see RRU Power Cable.

NEG(-)

CPRI0

Optical/electrical port 0, connected to the
BBU or an upper-level RRU

CPRI1

Optical/electrical port 1, connected to a
lower-level RRU or the BBU

(3) Indicator

RUN

For details, see 3.3 RRU Indicators.

ALM

ACT

VSWR

CPRI0

CPRI1



The port for transmitting RET signals is determined by the software.



Connect the

CPRI0

port to the BBU by default in the single-mode scenario.

3.3 RRU Indicators

This section describes six indicators on an RRU. They indicate the running status of the RRU.

For detailed positions of RRU indicators, see 3.2 RRU Ports.

Table 3-2 describes RRU indicators.

Table 3-2

RRU Indicators

Indicator

Color

Status

Meaning

RUN

Green

Steady on

The power input is available, but the board
is faulty.

Steady off

No power input is available , or the board is
faulty.

Blinking (on for
1s and off for 1s)

The board is running properly.

Содержание RRU5303








































































































































Результаты поиска

Содержание RRU5303

Отзывы:

Похожие инструкции для RRU5303

Бренды по названию

Популярные бренды

Huawei RRU5303, Руководство по установке

Результаты поиска

Содержание RRU5303

Отзывы:

Похожие инструкции для RRU5303

Бренды по названию

Популярные бренды