Huawei RRU3201 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 96

background image

About This Document

Purpose

This document describes the process of installing a DC RRU3201 (referred to as RRU in this
document).

Product Versions

The following table lists the product versions related to this document.

Product Name

Product Version

DBS3900

V100R004C00 and later versions

DBS3900 LTE

V100R003C00 and later versions

Intended Audience

This document is intended for:

Base station installation engineers

Organization

1 Changes in the RRU3201 Installation Guide

This chapter describes the changes in the

RRU3201 Installation Guide

.

2 Installation Preparations

This chapter describes the reference documents, tools, and instruments that must be ready before
the installation. In addition, it specifies the skills and prerequisites that installation engineers
must have.

3 Information About the Installation

Before installing an RRU, you must be familiar with its exterior, ports, installation options,
physical supports, and installation clearance requirements.

4 Unpacking the Equipment

RRU3201
Installation Guide

About This Document

Issue 06 (2012-04-16)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

ii

«
1
2
3
4
5
...
»

Содержание RRU3201

































































































Отзывы:

Нет отзывов

Похожие инструкции для RRU3201

Бренд: Klarstein Страницы: 96

Бренд: Napoleon Страницы: 2

Бренд: Parrot Страницы: 19

Бренд: Parrot Страницы: 88

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 11

CK 3000 Evolution

Бренд: Parrot Страницы: 8

CK 3000 Evolution

Бренд: Parrot Страницы: 106

Бренд: Kabuto Страницы: 12

Бренд: Naterial Страницы: 40

Бренд: Takara Belmont Страницы: 36

Бренд: Van Air Systems Страницы: 8

Бренд: Klarstein Страницы: 24

Бренд: SpectraLink Страницы: 14

ALK.00.733.15000/B

Бренд: SW-Motech Страницы: 14

Бренд: turck Страницы: 12

Бренд: Thule Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды