Huawei NetCol5000-C030H90D0 Скачать руководство пользователя страница 96

Страница: 96 / 206

Sets and checks teamwork control information based on the requirements of

the smart cooling product.

●

Running
Checks the component status, system parameters, and the name, control and

operating status, and other related information of the components in the

current smart cooling product system.

●

Alarms
Checks the active and historical alarms of the smart cooling product, and

deletes the historical alarms.

●

Settings
Sets the involved parameters for the operation of the smart cooling product.

●

Maint
Checks or deletes the logs or component total runtime/run factor, manually

diagnoses each component, calibrates the sensor and touch screen, exports

data, and upgrades the system.

●

About
Checks the model, manufacturer, monitoring version, detail version

information, and electronic label of the ACC.

4.4 Initial Configuration

4.4.1 Setting Temperature and Humidity Values and

(Optional) Enabling T/H Sensors

Prerequisites

●

The T/H sensors outside the cabinet need to be enabled when they are

installed, otherwise, skip

Step 2

●

If you need to enable a humidity and temperature sensor, log in as the admin

user.

●

This section describes how to enable Cold aisle sensor 1.

Procedure

Step 1 On the home screen, choose Settings > System Settings > T/H sensor.

Figure 4-4

is displayed.

Figure 4-4 Setting temperature and humidity values

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

4 Commissioning

Issue 03 (2020-08-30)

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Huawei NetCol5000-C030H90D0, Руководство пользователя, Страница: 96 / 206

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы: