Huawei ME936 Скачать руководство пользователя страница 55

Страница: 55 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Electrical and Reliability Features

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Electrical and Reliability Features

5.1 About This Chapter

This chapter describes the electrical and reliability features of the interfaces in the
ME936 module, including:



Absolute Ratings



Operating and Storage Temperatures and Humidity



Power Supply Features



Reliability Features



EMC and ESD Features

5.2 Absolute Ratings

Table 5-1 lists the absolute ratings for the ME936 module. Using the ME936 module
beyond these conditions may result in permanent damage to the module.

Table 5-1

Absolute ratings for the ME936 module

Symbol

Specification

Min.

Max.

Unit

3.3V

External power voltage

–0.3

4.4

5.3 Operating and Storage Temperatures and Humidity

Table 5-2 lists the operating and storage temperatures and humidity for the ME936
module.

Содержание ME936


















































































Результаты поиска

Содержание ME936

Отзывы:

Бренды по названию

Популярные бренды

Huawei ME936, Руководство по оборудованию

Результаты поиска

Содержание ME936

Отзывы:

Бренды по названию

Популярные бренды