Huawei LUNA2000-30-S0 Скачать руководство пользователя

Страница: 118 / 129

7.4 Battery Storage and Recharge

Battery Acceptance Inspection

A battery recharge label must be put on the battery packing case. The recharge

label should contain the latest charge time and the next recharge time.

Battery Storage Requirements

1. Place batteries according to the signs on the packing case during storage. Do

not put batteries upside down or sidelong.

2. Stack battery packing cases by complying with the stacking requirements on

the external package.

3. Handle batteries with caution to avoid damage.
4. The storage environment requirements are as follows:

–

Ambient temperature: -10–55°C; recommended storage temperature: 20–

30°C

–

Relative humidity: 5% to 80%

–

Place batteries in a dry and clean place with proper ventilation.

–

Place batteries in a place that is away from corrosive organic solvents and

gases.

–

Keep batteries away from direct sunlight.

–

Keep batteries at least 2 meters away from heat sources.

5. The batteries in storage must be disconnected from external devices. The

indicators (if any) on the batteries should be off.

6. AC mains input voltage requirements in the recharge places: single-phase

power grid: 220 V/230 V/240 V, ±10%; three-phase voltage: 380 V/400 V,

±10%.

7. The warehouse keeper should collect battery storage information every

month and periodically report the battery inventory information to the

planning department. The batteries that have been stored for nearly 15

months (-10–25°C)

、

9 months (25–35°C) or 6 months (35–55°C) should be

recharged in a timely manner

8. Batteries should be delivered based on the "first in, first out" rule.
9. After the battery production test is complete and before the batteries are

stored, the batteries must be recharged to at least 50% of the SOC.

Conditions for Judging Overdue Storage

It is recommended that batteries not be stored for a long period. They should be

used soon after being deployed onsite. The batteries should be handled according

to the following requirements.

LUNA2000-(5-30)-S0

User Manual

7 System Maintenance

Issue 07 (2022-01-10)

111

Содержание LUNA2000-30-S0


































































































































Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды

Huawei LUNA2000-30-S0, Руководство пользователя

Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды