manualshive.com logo in svg

Huawei LampSite, Руководство по установке

Поделиться
Скачать
Huawei LampSite Скачать руководство пользователя страница 15

4.1 Information About the Installation

This section describes the information to be learnt before RHUB installation, including the
RHUB installation scenarios, clearance, and installation environment.

4.1.1 RHUB Installation Scenarios

An RHUB can be installed in a 19-inch cabinet, rack, shelf, or on a wall.

The RHUB supports that mounting ears are installed in standard mode or reverse mode. The
reverse mode is used by default. The two installation modes are defined as follows:

l

In standard mode, the front of the mounting ear is aligned with the RHUB panel, as shown
in 

Figure 4-1

.

Figure 4-1

 Installing mounting ears in standard mode

l

In reverse mode, the front of the mounting ear is 31 mm away from the RHUB panel, as
shown in 

Figure 4-2

.

Figure 4-2

 Installing mounting ears in reverse mode

LampSite
Installation Guide

4 Installing an RHUB

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

10

Содержание LampSite





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды