Huawei G5500 Скачать руководство пользователя страница 152

Страница: 152 / 215

Step 8

Install the cover of the GP608. For details, see

3.7 Cover

----End

6.4 G530 V2 Optional Part Installation

6.4.1 Installing a hard disk

Installing a hard disk

The G530 V2 supports a maximum of two 2.5-inch hard disks configured mixedly.

NOTE

You do not need to power off the G530 V2 before installing a hard disk.

Step 1

Determine the location for installing the hard disk.

Figure 6-25

shows the locations of hard

disks.

Figure 6-25

Locations of hard disks

Step 2

Take a spare hard disk out of its ESD bag.

Step 3

Raise the ejector lever completely and insert the hard disk into the slot. See (1) in

Figure

6-26

Figure 6-26

Installing a hard disk

FusionServer G5500 Server
User Guide

6 Optional Part Installation

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

144

Содержание G5500
























































































































































































































Результаты поиска

Содержание G5500

Отзывы:

Бренды по названию

Популярные бренды

Huawei G5500, Руководство пользователя

Результаты поиска

Содержание G5500

Отзывы:

Бренды по названию

Популярные бренды